F5 SERVICE MAUNAL.pdf - 第30页

1 Operational Safety SIPLACE 80S-20/F4/F4-6/F5 Ser vice Manual 1.2 Safety equipment E dition 04/98 1 - 20 1.2.5 Guard on the component table locations DANGER OO O All lo cations must b e equipped with fe eders i n order …

SIPLACE 80S-20/F4/F4-6/F5 Service Manual 1 Operational Safety

Edition 04/98 1.2 Safety equipment

1 - 19

Fig. 1.2.5 SIPLACE 80S-20/F

-6/’F

safety circuits

Start button pressed

Emergency stop button

pressed?

Protective cover open ?

Key switch

closed (position

Component table safety

circuit interrupted?

Yes

$FWLYH

K1 *) Yes

K2 *) Yes

9ROWDJH

y axis 100 V

x axis 100 V

Star axis 100 V

dp axis 30 V

z axis 30 V

$FWLYH

PCB conveyor Yes

PCB clamping deviceYes

Width adjustment Yes

PCB stopper Yes

Tape cutter Yes

Yes

$FWLYH

K1 *) No

K2 *) Yes

9ROWDJH

y axis 0 V

x axis 0 V

Star axis **) 10 V

dp axis 30 V

z axis 30 V

$FWLYH

PCB conveyor Yes

PCB clamping device No

Width adjustment Yes

PCB stopper No

Tape cutter No

$FWLYH

K1 *) No

K2 *) No

9ROWDJH

y axis 0 V

x axis 0 V

Star axis **) 10 V

dp axis 30 V

z axis 30 V

$FWLYH

PCB conveyor No

PCB clamping device No

Width adjustment No

PCB stopper No

Tape cutter No

*) K1, K2 protective contactor combination

**) The maximum current is limited by a 4.7 Ohm resistor.

Compressed air

min. 5.1 bar?

Yes

1 Operational Safety SIPLACE 80S-20/F4/F4-6/F5 Service Manual

1.2 Safety equipment Edition 04/98

1 - 20

1.2.5 Guard on the component table locations

DANGER OOO

All locations must be equipped with feeders in order to guarantee operational reliability. If there are not

enough conveyors available, a guard ("feeder dummy") must be fitted in place of the conveyor.

The following variants can be used:

Item no. 00116820-01 SIPLACE guard for 1 location

Item no. 00116821-01 SIPLACE guard for 6-10 locations

Item no. 00116822-01 SIPLACE guard for 11-20 locations

Fig. 1.2.6 Guard

-Key to Fig. 1.2.6

1 Guard for 1 location 2 Guard for 6-10 locations

3 Guard for 11-20 locations

SIPLACE 80S-20/F4/F4-6/F5 Service Manual 1 Operational Safety

Edition 04/98 1.3 Residual voltages in the servo unit and discharge times when placement system is switched off

1 - 21

 5HVLGXDOYROWDJHVLQWKHVHUYRXQ LWDQGG LVFKDUJH

WLPHVZKHQSODFHPHQWV\VWHPLVVZ LWFK HGRII

When the emergency stop button is pressed or the placement system is switched off, the electrolytic capaci-

tors quickly discharge to safe residual voltage levels via switched resistors on the discharge board

(00308443-xx).

The voltages can be tapped off at test sockets 001 - 009 on the voltmeter unit in the servo unit.

DANGER

Automatic placement systems from the SIPLACE family are powered with 3 x 400 V ± 10 %, 50/60 Hz mains

voltage.

This means that parts of the system carry potentially fatal voltages - even when switched off at the main

switch.

Death, serious injury or considerable damage may result if these placement systems are handled incorrectly.

Always follow the applicable accident prevention and VDE regulations (particularly VDE 0113).

The guard over the servo unit must ONLY be opened by appropriately qualified and trained personnel.

Fig. 1.3.1 Test sockets on the voltmeter unit in the servo unit

un-

switched

Servo

unit