F5 SERVICE MAUNAL.pdf - 第336页

9 12-Segment Revolver Head (10000) SIPLACE 80S-20/F4 Service Manual 9.9 12x Nozzle Cha nger Edition 07/97 9 - 40  6WHS VIRU,QVW DOOLQJWKH0DJD]LQH ● Place the maga zine o n the asso ciated locat ing pin s (see …

100%1 / 483
SIPLACE 80S-20/F4 Service Manual 9 12-Segment Revolver Head (10000)
Edition 07/97 9.9 12x Nozzle Changer
9 - 39
.H\WR)LJ
1 Magazine for type 7.xx nozzles
2 Advancing pins
3 Locating pins
4 Magazine fixing screw
5 Supporting rail
 6WHSVIRU5HPRYLQJWKH0DJD]LQH
● Loosen the M3x15 screw (see Fig. 9.9.2, item 4) with a hexagon socket-head spanner, size 2.5.
● Remove the magazine from the supporting rail. You may feel a slight resistance when you remove the
magazine. This is normal since the magazine is also secured to the screw with magnets.
9 12-Segment Revolver Head (10000) SIPLACE 80S-20/F4 Service Manual
9.9 12x Nozzle Changer Edition 07/97
9 - 40
 6WHSVIRU,QVWDOOLQJWKH0DJD]LQH
● Place the magazine on the associated locating pins (see Fig. 9.9.2, item 3) and the advancing pin (see Fig.
9.9.2, item 2).
● Push down lightly on the magazine until it lies on the support.
● Insert the M3x15 screw and tighten the screw with a hexagon socket-head spanner, size 2.5.
 5HSODFLQJWKH1R]]OH&KDQJHU&RQWURO%RDUG
6SDUHSDUWV
– Nozzle changer control board, item no. 00317353-02
7RROV
– Hexagon socket-head spanner, size 2.5
 6WHSVIRU5HPRYLQJWKH1R]]OH&KDQJHU&RQWURO%RDUG
● Remove the nozzle changer from the machine as described in section 9.9.1.
● Remove the connecting cable between the 5/2-way valve and plug X2 on the control board.
● Loosen the 4 M3x8 screws (see Fig. 9.9.3, item 9).
● Remove the control board by moving it towards the reject station (see Fig. 9.9.3,
item 11). When you do this, be careful not to damage the actuating plate of the light barrier.
PLEASE NOTE
Do not carry out any work on the actuating plate of the light barrier. This plate is set and coated at the factory.
 6WHSVIRU,QVWDOOLQJWKH1R]]OH&KDQJHU&RQWURO%RDUG
● Introduce the control board into the nozzle changer from the reject station side.
● Screw down the board using the 4 M3x8 screws.
● Fit the connecting cable between the 5/2-way valve and plug X2 on the control board.
● Install the nozzle changer in the machine as described in section 9.9.2.
SIPLACE 80S-20/F4 Service Manual 9 12-Segment Revolver Head (10000)
Edition 07/97 9.9 12x Nozzle Changer
9 - 41
.H\WR)LJ
1 Supporting rail
2 Cylinder fixing screws
3 Valve block fixing screws
4 Nozzle changer control board
5 Control cable plug
65/2-way valve
7 Connections for the cylinder connecting hoses
8 Cylinder
9 Control board fixing screws
10 Reject station fixing screws
11 Complete reject station