00191494-01.pdf - 第102页

Error Messages Short Reference SIPLACE 80 S-15/F3/G 03/99 Issue Software Version SR.010.x x 100 1038 Z-axis; GU2: deactivated CAUSE ● Axis has been deactiva ted at the axis board (servo ) REMEDY ● Switch on the axis at t…

100%1 / 124
Short Reference SIPLACE 80 S-15/F3/G Error Messages
03/99 Issue Software Version SR.010.xx
99
1031 Z-axis; GU2: Position control does not work
CAUSE
● The position control of the axis is not working properly; machine data are not correct
REMEDY
● Switch off the machine (reset), check axis for stiffness of running; check the machine data
1032 Z-axis; GU3: Position control does not work
CAUSE
● The position control of the axis is not working properly; machine data are not correct
REMEDY
● Switch off the machine (reset), check axis for stiffness of running; check the machine data
1033 X-axis: deactivated
CAUSE
● Axis has been deactivated at the axis board (servo)
REMEDY
● Switch on the axis at the axis card
1034 Y-axis: deactivated
CAUSE
● Axis has been deactivated at the axis board (servo)
REMEDY
● Switch on the axis at the axis card
1035 xk-axis: deactivated
CAUSE
● Axis has been deactivated at the axis board (servo)
REMEDY
● Switch on the axis at the axis card
1036 yk-axis: deactivated
CAUSE
● Axis has been deactivated at the axis board (servo)
REMEDY
● Switch on the axis at the axis card
1037 Z-axis; GU1: deactivated
CAUSE
● Axis has been deactivated at the axis board (servo)
REMEDY
● Switch on the axis at the axis card
Error Messages Short Reference SIPLACE 80 S-15/F3/G
03/99 Issue Software Version SR.010.xx
100
1038 Z-axis; GU2: deactivated
CAUSE
● Axis has been deactivated at the axis board (servo)
REMEDY
● Switch on the axis at the axis card
1039 Z-axis; GU3: deactivated
CAUSE
● Axis has been deactivated at the axis board (servo)
REMEDY
● Switch on the axis at the axis card
1040 X-axis: Timeout
CAUSE
● Axis does not reach position within the specified time; axis setting is not correct; machine data not
correct; drive motor, tachometer, incremental encoder, servo-amplifier defective;
mechanism is jamming
REMEDY
● Check the axis calibration; check machine data; or check the components; if necessary, replace;
check the mechanism;
1041 Y-axis: Timeout
CAUSE
● Axis does not reach position within the specified time; axis setting is not correct; machine data not
correct; drive motor, tachometer, incremental encoder, servo-amplifier defective;
mechanism is jamming
REMEDY
● Check the axis calibration; check machine data; or check the components; if necessary, replace;
check the mechanism;
1042 xk-axis: Timeout
CAUSE
● Axis does not reach position within the specified time; axis setting is not correct; machine data not
correct; drive motor, tachometer, incremental encoder, servo-amplifier defective;
mechanism is jamming
REMEDY
● Check the axis calibration; check machine data; or check the components; if necessary, replace;
check the mechanism;
1043 yk-axis: Timeout
CAUSE
● Axis does not reach position within the specified time; axis setting is not correct; machine data not
correct; drive motor, tachometer, incremental encoder, servo-amplifier defective;
mechanism is jamming
REMEDY
● Check the axis calibration; check machine data; or check the components; if necessary, replace;
check the mechanism;
Short Reference SIPLACE 80 S-15/F3/G Error Messages
03/99 Issue Software Version SR.010.xx
101
1044 Z-axis; GU1: Timeout
CAUSE
● Axis does not reach position within the specified time; axis setting is not correct; machine data not
correct; drive motor, tachometer, incremental encoder, servo-amplifier defective;
mechanism is jamming.
REMEDY
● Check the axis calibration; check machine data; or check the components; if necessary, replace;
check the mechanism;
1045 Z-axis; GU2: Timeout
CAUSE
● Axis does not reach position within the specified time; axis setting is not correct; machine data not
correct; drive motor, tachometer, incremental encoder, servo-amplifier defective;
mechanism is jamming.
REMEDY
● Check the axis calibration; check machine data; or check the components; if necessary, replace;
check the mechanism;
1046 Z-axis; GU3: Timeout
CAUSE
● Axis does not reach position within the specified time; axis setting is not correct; machine data not
correct; drive motor, tachometer, incremental encoder, servo-amplifier defective;
mechanism is jamming.
REMEDY
● Check the axis calibration; check machine data; or check the components; if necessary, replace;
check the mechanism;
1047 X-axis: Target position outside of travel range
CAUSE
● The measurement of the head references does not match the travel range of the X-axis.
REMEDY
● Remeasure the head references; remeasure the minimum/maximum positions of the axis.
1048 Y-axis: Target position outside of travel range
CAUSE
● The measurement of the head references does not match the travel range of the Y-axis.
REMEDY
● Remeasure the head references; remeasure the minimum/maximum positions of the axis.
1049 xk-axis: Target position outside of travel range
CAUSE
● The measurement of the head references does not match the travel range of the xk-axis
REMEDY
● Remeasure the head references; remeasure the minimum/maximum positions of the axis