00191494-01.pdf - 第24页
Error Messages Short Reference SIPLACE 80 S-15/F3/G 03/99 Issue Software Version SR.010.x x 22 238 Stopper jam during retraction CAUSE ● Compressed air lacking; back pressure too high; sto pper defective. REMEDY ● Check …
Short Reference SIPLACE 80 S-15/F3/G Error Messages
03/99 Issue Software Version SR.010.xx
21
231 No PCB on the input conveyor
CAUSE
● The PCB board was removed while being transported onto the central conveyor; sensor defec-
tive.
REMEDY
● Under the menu "Transportation error" continue placement, place board on input conveyor; fit
new sensor.
232 The lifting table cannot be moved downwards
CAUSE
● Beros defective; cutout triggered.
REMEDY
● fit new Beros; close lifting table cutout.
233 Command to coplanarity is not complete
CAUSE
● Package form data, set-up erroneous.
REMEDY
● Re-assign set-up, repeat measurement.
234 The lifting table cannot be moved upwards
CAUSE
● Beros defective; cutout triggered.
REMEDY
● Fit new Beros; close lifting table cutout.
235 Center conveyor light barrier is not released
CAUSE
● PCB board jamming in the central conveyor; sensor defective.
REMEDY
● Correct the jamming; fit new sensor.
236 PCB does not reach the center conveyor
CAUSE
● PCB board jamming in the center conveyor; sensor defective.
REMEDY
● Correct the jamming; fit new sensor.
237 Stopper jam during extension
CAUSE
● Compressed air lacking; back pressure too high; stopper defective.
REMEDY
● Check compressed air; adjust back pressure; replace stopper.
Error Messages Short Reference SIPLACE 80 S-15/F3/G
03/99 Issue Software Version SR.010.xx
22
238 Stopper jam during retraction
CAUSE
● Compressed air lacking; back pressure too high; stopper defective.
REMEDY
● Check compressed air; adjust back pressure; replace stopper.
239 Component description of coplanarity is not complete
CAUSE
● Package form data erroneous.
REMEDY
● Check package form data and respecify set-up.
240 Command data format to coplanarity is invalid
CAUSE
● Package form data, set-up, cluster erroneous.
REMEDY
● Check and respecify package form data, set-up, cluster.
241 Coplanarity tolerance is zero
CAUSE
● Coplanarity tolerance (max. component height tolerance) in the set-up for the placement positi-
ons of the circuit image is zero.
REMEDY
● Increase coplanarity tolerance (max. component height tolerance) and respecify set-up and clu-
ster.
242 No PCB on the center conveyor
CAUSE
● Transportation onto output conveyor was started under single functions although there is no
board on the center conveyor; sensor in the center conveyor defective.
REMEDY
● Only start transportation onto the output conveyor under single functions when there is a board
on the center conveyor; fit new sensor.
243 PCB does not reach the output conveyor
CAUSE
● PCB board jamming in the center conveyor; sensor defective.
REMEDY
● Correct the jamming; fit new sensor.
Short Reference SIPLACE 80 S-15/F3/G Error Messages
03/99 Issue Software Version SR.010.xx
23
244 Center conveyor occupied
CAUSE
● When the function "Board to center conveyor" started there already was a PCB board on the cen-
ter conveyor; sensor defective.
When the belt speed was set the center conveyor was occupied.
REMEDY
● Remove the PCB board; fit new sensor.
245 Output conveyor occupied
CAUSE
● When the function "Board to output conveyor" started there already was a PCB board on the out-
put conveyor; sensor of output conveyor defective.
When the belt speed was set output conveyor was occupied.
REMEDY
● Remove the PCB board; fit new sensor.
246 BERO of left table side is not activated
CAUSE
● Bero is not covered.
REMEDY
● Check Bero.
247 Error in axis programming (left table side)
CAUSE
● Bero of the left table side defective; axis could not be moved.
REMEDY
● Check Bero; reboot.
248 BERO of left table side responding constantly
CAUSE
● Bero constantly covered.
REMEDY
● Check Bero.
249 Width adjustment at limit switch maximum width
CAUSE
● Width adjustment moved up to the limit switch; limit switch defective.
REMEDY
● Move width adjustment in other direction; fit new limit switch.
250 Width adjustment at limit switch minimum width
CAUSE
● Width adjustment moved up to the limit switch; limit switch defective.
REMEDY
● Move width adjustment in other direction; fit new limit switch.