MDO3000 Programmer Manual.pdf - 第537页

Commands Listed in Alphabetical Order POWer:RIPPle :SOUrce This command specifies the source waveform for ripple tests . The voltage so urce waveform is specified using the POW er:VOL T AGESOurce command and the current wa…

100%1 / 1158
Commands Listed in Alphabetical Order
Syntax
POWer:RIPPle:
RESults:MEAN?
Examples
POWER:RIPPLE:RESULTS:MEAN? might return
:POWER:RIPPLE:RESULTS:MEAN 1.0 indicating that the mean peak-to-peak
amplitude is set to 1.0 V.
POWer:RIPPle:RESults:MIN? (Query Only)
Returns the minimum of the peak-to-peak ripple measurement.
Conditions
This command requires a DPO4PWR application module for 4000 series models,
or an MDO3PWR application module for MDO3000 series models.
Group
Power
Syntax
POWer:RIPPle:RESults:MIN?
Examples
POWER:RIPPLE:RESULTS:MIN? might return :POWER:RIPPLE:R ESULTS:MIN
0.9
indicating that the minimum peak-to-peak amplitude is set to 0
.9 V.
POWer:RIPPle:RESults:STDdev? (Query Only)
Returns the standard deviation of the peak-to-peak ripple measurements.
Conditions
This command requires a DPO4PWR application module for 4000 series models,
or an MDO3PWR application module for MDO3000 series models.
Group
Power
Syntax
POWer:RIPPle:RESults:STDdev?
Examples
POWER:RIPPLE:RESULTS:STDDEV? might return
:POWER:RIPPLE:RESULTS:STDDEV 0.14 indicating that the standard
deviation of the peak-to-peak amplitude is set to 0.14.
2-506 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Commands Listed in Alphabetical Order
POWer:RIPPle
:SOUrce
This command specifies the source waveform for ripple tests. The voltage source
waveform is specified using the POWer:VOLTAGESOurce command and the
current wave
form is specified using the POWer:CURRENTSOurce command.
Conditions
This command requires a DPO4PWR application module for 4000 series models,
or an MDO3PWR application module for MDO3000 series models.
Group
Power
Syntax
POWer:RIPPle:SOUrce {VOLTage|CURRent}
Arguments
VOLTage specifies voltage source waveform for ripple tests.
CURRent specifies current source waveform for ripple tests.
Examples
POWER:RIPPLE:SOURCE CURRent sets the ripple source to Current.
POWER:RIPPLE:SOURCE? might return :POWER:RIPPLE:SOURCE VOLT
indicating that the ripple source is set to Voltage.
POWer:SOA:LINear:XMAX
This command specifies the user XMAX value for use in linear SOA calculations.
Conditions
This command requires a DPO4PWR application module for 4000 series models,
or an MDO3PWR application module for MDO3000 series models.
Group
Power
Syntax
POWer:SOA:LINear:XMAX <NR3>
POWer:SOA:LINear:XMAX?
Arguments
<NR3> is a floating point number that specifies the XMAX value used for linear
SOA calculations.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-507
Commands Listed in Alphabetical Order
Examples
POWER:SOA:LIN
EAR:XMAX 700
sets the XMAX value to 700.0000.
POWER:SOA:LINEAR:XMAX ? might return :POWER:SOA:LIN ear:XMAX
500.0000
indi
cating that the XMAX value for linear plot type is set to 500.0000.
POWer:SOA:LINear:XMIN
This command specifies the user XMIN value for use in linear SOA calculations.
Conditions
This command requires a DPO4PWR application module for 4000 series models,
or an MDO3PWR application module for MDO3000 series models.
Group
Power
Syntax
POWer:SOA:LINear:XMIN <NR3>
POWer:SOA:LINear:XMIN?
Arguments
<NR3> is a floating point numb
er that specifies the XMIN value used for linear
SOA calculations.
Examples
POWER:SOA:LINEAR:XMIN 2 sets the XMIN value to 2.0000.
POWER:SOA:LINEAR:XMIN ? might return :POWER:SOA:LIN ear:XMIN
0.0E+0
indicating that the XMIN value for linear plot type is set to 0.0E+0.
POWer:SOA:LINear:YMAX
This command specifies the user YMAX value for use in linear SOA calculations.
Conditions
This command requires a DPO4PWR application module for 4000 series models,
or an MDO3PWR applic
ation module for MDO3000 series models.
Group
Power
Syntax
POWer:SOA:LINear:YMAX <NR3>
POWer:SOA:LINear:YMAX?
Arguments
<NR3> is a floating point number that specifies the YMAX value used for linear
SOA calculations.
2-508 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual