MDO3000 Programmer Manual.pdf - 第694页

Commands Listed in A lphabetical Order SEARCH:SEARC H<x>:TRIGger:A:BUS:B<x>:I2C:ADDRess:V ALue This command spec ifies the address value to be used in an I2C search if the sea rch condition is ADDRess or ADDRA…

100%1 / 1158
Commands Listed in Alphabetical Order
Conditions
This command re
quires a DPO4EMBD application module for DPO/MSO4000B
and MDO4000/B/C models or MDO3EMBD application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe
{ADDR7|ADDR10}
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:ADDRess:MODe?
Arguments
ADDR7 specifies 7-bit addresses.
ADDR10 specifies 10-bit addresses.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe
This command specifies the I2C address type to be used in an I2C search.
SEARCH<x> is the search number, which is always 1, and B<x>
Conditions
This command requires a DPO4EMBD application module for DPO/MSO4000B
and MDO4000/B/C models or MDO3EMBD application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe
{GENeralcall|STARtbyte|HSmode|EEPROM|USER}
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:ADDRess:TYPe?
Arguments
GENeralcall specifies the GENeralcall address type.
STARtbyte specifies the STARtbyte address type.
HSmode specifies the HSmode address type
EEPROM specifies the EEPROM address type.
USER specifies a user address.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-663
Commands Listed in Alphabetical Order
SEARCH:SEARC
H<x>:TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue
This command specifies the address value to be used in an I2C search if the search
condition is
ADDRess or ADDRANDDATA (address and data). SEARCH<x> is the
search numbe
r, which is always 1, and
B<x>
Conditions
This command requires a DPO4EMBD application module for DPO/MSO4000B
and MDO400
0/B/C models or MDO3EMBD application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue <bin>
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:ADDRess:VALue?
Related Commands
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:CONDition
Arguments
<bin> is the address in binary format.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:CONDition
This command specifies the search condition to use for an I2C search. SEARCH< x>
is the search number, which is always 1, and B<x>
Conditions
This command requires a DPO4EMBD application module for DPO/MSO4000B
and MDO4000/B/C models or MDO3EMBD application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:CONDition
{STARt|STOP|REPEATstart|ACKMISS|ADDRess|DATA|ADDRANDDATA}
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:CONDition?
Arguments
STARt sp
ecifies a search based on a start condition.
STOP specifies a search based on a stop condition.
REPEATstart specifies a search based on a repeat of start condition.
ACKMISS specifies a search based on a missing acknowledgement condition.
2-664 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Commands Listed in Alphabetical Order
ADDRess specifi
es a search based on an address.
DATA specifies a search based on a data condition.
ADDRANDDATA specifies a search based on an address and data condition.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:DATa:DIRection
This comman
d specifies the data direction to use for an I2C search: either read,
write, or either.
SEARCH<x> is the search number, which is always 1, and B<x>
Conditions
This command requires a DPO4EMBD application module for DPO/MSO4000B
and MDO4000/B/C models or MDO3EMBD application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:DATa:DIRection
{READ|WRITE|NOCARE}
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:DATa:DIRection?
Arguments
READ specifies a read condition.
WRITE specifies a write condition.
NOCARE specifies either a read or write condition.
SEARCH:SEARCH<x>:TR
IGger:A:BUS:B<x>:I2C:DATa:SIZe
This command specifies the length of the data string, in bytes, to be used for an
I2C search, if the search condition is set to
DATA or ADDRAN DDATA (address and
data).
SEARCH<x> is
the search number, which is always 1, and
B<x>
Conditions
This command requires a DPO4EMBD application module for DPO/MSO4000B
and MDO4000/B/C models or MDO3EMBD application module for
MDO3000 models.
Group
Search
Syntax
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:DATa:SIZe <NR1>
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:DATa:SIZe?
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-665