MDO3000 Programmer Manual.pdf - 第598页
Commands Listed in A lphabetical Order Examples RF:PROBE:GAIN ? might return RF:PROBE:GA IN 0.1000E+0 0 indicating that the attached 10x probe delivers 1 V to the RF input for every 10 V applied to th e probe input. RF:P…
Commands Listed in Alphabetical Order
PASSED indicat
es the probe is degaussed.
FAILED indicates the degauss operation failed.
RUNNING indicates the probe degauss operation is currently in progress.
Examples
RF:PROBE:DEGAUSS:STATE? might return FAILED, indicating the degauss
operation failed.
RF:PRObe:FORCEDRange
This command specifies the range of a TekVPI probe attached to the RF input.
Conditions
MDO3
000, MDO4000/B, or MDO4000C models with option SA3 or SA6 only.
Group
RF
Syntax
RF:PRObe:FORCEDRange <NR3>
RF:PRObe:FORCEDRange?
Arguments
<NR3> is a floating point number that specifies the range, which is probe specific.
Returns
The query form of this command returns 0.0 for probes that do not support
forced ranges.
RF:PRObe:GAIN
This command specifies the scale factor for the probe attached to the RF input.
Conditions
MDO3000, MDO4000/B, or MDO4000C models with option SA3 or SA6 only.
Group
RF
Syntax
RF:PRObe:GAIN <NR3>
RF:PRObe:GAIN?
Arguments
<NR3> is a floating point number that specifies the probe scale factor. Allowed
values depend on the specific probe.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-567
Commands Listed in Alphabetical Order
Examples
RF:PROBE:GAIN
?
might return RF:PROBE:GAIN 0.1000E+00 indicating that
the attached 10x probe delivers 1 V to the RF input for every 10 V applied to the
probe input.
RF:PRObe:ID
:SERnumber? (Query Only)
This query returns the serial number of the probe attached to the RF input.
NOTE. For Level 0 and 1 probes, the serial number will be "".
Condition
s
MDO3000, MDO4000/B, or MDO4000C models with option SA3 or SA6 only.
Group
RF
Syntax
RF:PRObe:ID:SERnumber?
Related Commands
RF:PRObe:ID:TYPe?
Examples
RF:PROBE:ID:SERNUMBER? might return :RF:PROBE:ID:SERNUMBER
"B010289"
indicating
that the serial number of the probe attached to the RF
input is B010289.
RF:PRObe:ID:TYPe? (Query Only)
This query returns the type of probe attached to the RF input. Level 2 (or higher)
probes supply their exact product nomenclature; for Level 0 or 1 probes, a generic
*“No Probe Detected” message is returned.
Conditions
MDO3000, MDO4000/B, or MDO4000C models with option SA3 or SA6 only.
Group
RF
Syntax
RF:PRObe:ID:TYPe?
Related Commands
RF:PRObe:ID:SERnumber?
2-568 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Commands Listed in Alphabetical Order
Examples
RF:PROBE:ID:T
YPE?
might return :RF:PROBE:ID:TYPE "P6203" indicating
that P6203-type probe is attached to the RF input.
RF:PRObe:PREAmp:MODe
Sets or returns the user-selected mode for an RF pre-amp connected to the RF
input - either
BYPass or AUTO.
Note that the actual status of the pre-amp (either
NONE, ON or BYPass)is
determined by the selected mode along with the RF reference level. You can query
the status of the pre-amp using the command RF:PRObe:PREAmp:STATus?
Conditions
MDO3000, MDO4000/B, or MDO4000C models with option SA3 or SA6 only.
Group
RF
Syn
tax
RF:PRObe:PREAmp:MODe <BYPass|AUTO>
RF:PRObe:PREAmp:MODe?
Related Commands
RF:PRObe:PREAmp:STATus?
Arguments
BYPass means the pre-amp will not amplify the signal. When the mode is set to
BYPass, the pre-amp amplification is always off, regardless of the RF reference
level.
AUTO means the pre-amp will turn its amplification on or off based on the RF
reference level. When the
MODe is set to AUTO and the RF reference level is below
the RF reference level threshold, then the pre-amp amplification is automatically
turned on, and the
STATus is set to ON. When the RF reference level is at or above
the RF reference level threshold, then the pre-amp amplification is automatically
turned off, and the
STATus is set to BYPass.
NOTE. The RF reference level threshold for the TPA-N-PRE model pre-amp is
-25 dBm on MDO4000/B/C models, and -15 dBm on MDO3000 models.
Examples
RF:PRObe:PREAmp:MODe BYP sets the preamp so that it will not amplify the
signal.
RF:PRObe:PREAmp:MODe? might return AUTO, indicating that the pre-amp
amplification has been set to turn on or off depending on whether the RF reference
level is above or below the RF reference level threshold.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-569