MDO3000 Programmer Manual.pdf - 第840页

Commands Listed in A lphabetical Order Syntax TRIGger:A:BUS :B<x>:FLEXray:CY CLEcount:HIVALu e <QString> TRIGger:A:BUS :B<x>:FLEXray:CY CLEcount:HIVALu e? Arguments <QString> i saq u o t e ds t r …

100%1 / 1158
Commands Listed in Alphabetical Order
Conditions
This command re
quires a DPO4AUTOMAX application module for
DPO/MSO4000B and MDO4000/B/C models or MDO3FLEX application module
for MDO3000 models.
Group
Trigger
Syntax
TRIGger:A:BUS:B<x>:FLEXray:CONDition
{SOF|FRAMEType|IDentifier|CYCLEcount|HEADer|DATA
|IDANDDATA|EOF|ERROR}
TRIGger:A:BUS:B<x>:FLEXray:CONDition?
Arguments
SOF sets the trigger condition to start of frame.
FRAMEType sets the trigger condition to frame type.
IDentifier sets the trigger condition to identifier.
CYCL
Ecount
sets the trigger condition to cycle count.
HEADer sets the trigger condition to header.
DATA sets the trigger condition to data.
IDANDDATA sets the trigger condition to id and data.
EOF sets the trigger condition to end of frame.
ERROR sets the trigger condition to error.
Examples
TRIGGER:A:BUS:B1:FLEXRAY:CONDITION? might return
TRIGGER:A:BUS:B1:FLEXRAY:CONDITION SOF indicating the
FlexRay condition is start of frame.
TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue
This command specifies the high value when triggering on a FlexRay bus cycle
count field. (Use TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue to
set the low value.) The trigger condition must be set to CYCLEcount (using
TRIGger:A:BUS:B<x>:FLEXray:CONDition).
B<x>
Conditions
This command requires a DPO4AUTOMAX application module for
DPO/MSO4000B and MDO4000/B/C models or MDO3FLEX application module
for MDO3000 models.
Group
Trigger
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-809
Commands Listed in Alphabetical Order
Syntax
TRIGger:A:BUS
:B<x>:FLEXray:CYCLEcount:HIVALue <QString>
TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue?
Arguments
<QString> isaquotedstringthatisthecyclecounthighvalue.
Examples
TRIGGER:A:BUS:B1:FLEXRAY:CYCLECOUNT:HIVALUE “110010” sets the
cycle count high value to 110010.
TRIGGER:A:BUS:B1:FLEXRAY:CYCLECOUNT:HIVALUE? might return
TRIGGER:A:BUS:B1:FLEXRAY:CYCLECOUNT:HIVALUE "XXXXXX" indicating
the cycle count high value is don't care.
TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier
This command specifies the qualifier (<, >, =, <=, >=, not =, in
range, out of range) to use when triggering on the FlexRay bus cycle
count field. The trigger condition must be set to CYCLEcount (using
TRIGger:A:BUS:B<x>:FLEXray:CONDition).
B<x>
Conditions
This command requires a DPO4AUTOMAX application module for
DPO/MSO4000B and MDO4000/B/C models or MDO3FLEX application module
for MDO3000 models.
Group
Trigger
Syntax
TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier
{LESSthan|MOREthan|EQual|UNEQual|LESSEQual|MOREEQual|
INrange|OUTrange}
TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:QUALifier?
Arguments
LESSthan sets the cycle count qualifier to less than.
MOREthan sets the cycle count qualifier to more than.
EQual sets the cycle count qualifier to equal.
UNEQual sets the cycle count qualifier to not equal.
LESSEQual sets the cycle count qualifier to less than or equal.
MOREEQual sets the cycle count qualifier to greater than or equal.
INrange sets the cycle count qualifier to in range.
OUTrange sets the cycle count qualifier to out of range.
2-810 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Commands Listed in Alphabetical Order
Examples
TRIGGER:A:BUS
:B1:FLEXRAY:CYCLECOUNT:QUALIFIER LESSTHAN
sets the
cycle count qualifier to LESSTHAN.
TRIGGER:A:BU
S:B1:FLEXRAY:CYCLECOUNT:QUALIFIER?
might return
TRIGGER:A:BUS:B1:FLEXRAY:CYCLECOUNT:QUALIFIER EQUAL indicating
that the cycle count qualifier is set to EQUAL.
TRIGger:A:
BUS:B<x>:FLEXray:CYCLEcount:VALue
This command specifies the low value when triggering on the FlexRay bus cycle
count field. (Use TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:HIVALue to
set the up
per value.) The trigger condition must be set to CYCLEcount (using
TRIGger:A:BUS:B<x>:FLEXray:CONDition).
B<x>
Conditions
This command requires a DPO4AUTOMAX application module for
DPO/MSO4000B and MDO4000/B/C models or MDO3FLEX application module
for MDO3000 models.
Group
Trigger
Syntax
TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue <QString>
TRIGger:A:BUS:B<x>:FLEXray:CYCLEcount:VALue?
Arguments
<QString> is a quoted binary data string that represents the cycle count low
value.
Examples
TRIGGER:A:BUS:B1:FLEXRAY:CYCLECOUNT:VALUE “11001101” sets the
cycle count value to 11001101.
TRIGGER:A:BUS:B1:FLEXRAY:CYCLECOUNT:VALUE? might return
TRIGGER:A:BUS:B1:FLEXRAY:CYCLECOUNT:VALUE "XXXXXX" indicating the
cycle count value is don't care.
TRIGger:A:BUS:B<x>:FLEXray:DATa:HIVALue
This command specifies the high value when triggering on the FlexRay bus
data field. (Use TRIGger:A:BUS:B<x>:FLEXray:DATa:VALue to set the lower
value.) The trigger condition needs to be set to ID or IDANDDATA (using
TRIGger:A:BUS:B<x>:FLEXray:CONDition).
B<x>
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-811