SIPLACE D4-D4i 工程师手册_EN.pdf - 第59页
Service Work 4.1.4 Axis Unit Electrical System Service Manual SIPLACE D4/D4i 59 Replacing the A364 Axis Card ► End all placement operations with the machine. ► Switch the placement syst em off at the main switch. ► You c…
Service Work
Electrical System 4.1.3 Distributors in Sectors 1-4
58 Service Manual SIPLACE D4/D4i
4.1.3
4.1.3 Distributors in Sectors 1-4
Distributors in Sectors 1-4
4.1.3.1
4.1.3.1 Replacing parts
Replacing parts
The assemblies are located behind the covers in the relevant sectors. The assemblies are fixed to profile
rails and are connected via terminal strips.
► Undo and remove the fastening screws from the relevant cover. Remove the cover.
► Mark the assembly connections for later reference.
► Loosen the assembly connections.
► Lift the assembly off the profile bar. Loosen any fastening screws.
4.1.4
4.1.4 Axis Unit
Axis Unit
4.1.4.1
4.1.4.1 Replacing parts
Replacing parts
► End all placement operations with the machine.
► Switch the placement system off at the main switch.
► You can now access the axis unit at the required location (1/4 or 2/3).
Complete Axis Unit
DIP switch on the backplane
Legend
If the axis unit has been replaced, you will need to configure the axis unit for the relevant installation po-
sition. This involves adjusting the DIP switch on the backplane accordingly.
1 Position of DIP switch on the backplane 3 Setting for axis unit at location 2/3
2 Setting for axis unit at location 1/4
Service Work
4.1.4 Axis Unit Electrical System
Service Manual SIPLACE D4/D4i 59
Replacing the A364 Axis Card
► End all placement operations with the machine.
► Switch the placement system off at the main switch.
► You can now access the axis unit at the required location (1/4 or 2/3).
► Loosen the screws holding the relevant axis card.
► Remove the axis card from the unit by moving the release lever up and down.
► Insert the new axis card and push the assembly in (you will feel a slight resistance) until it engages
and then tighten the two fastening screws.
► Switch the machine on again.
A364 axis cards on the D2/D4
Legend for D4
Gantry numbers for PA1 (in brackets for PA2)
1. X ,Y , star and Z axis for gantry 1 (2)
2. X ,Y , star and Z axis for gantry 4 (2)
3. DP axis for gantry 1 and 4 (2 and 3)
4. Release lever with screwed connection
Service Work
Gantry 4.2.1 Preparations for Service Work
60 Service Manual SIPLACE D4/D4i
Firmware download
Replacing the Servo Card
4.2
4.2 Gantry
Gantry
4.2.1
4.2.1 Preparations for Service Work
Preparations for Service Work
► End all placement operations on the placement system.
► Disconnect the changeover table of the gantry concerned, if necessary.
► Switch the placement system off at the main switch.
► Wait until the operating system has shut down and the UPS has switched off.
► Disconnect the machine from the power supply.
► Disconnect the placement system from the compressed air supply.
Overview of firmware download
► Start SITEST.
► Download the firmware for the relevant axes. To do
this, select "Settings" from the SITEST menu bar and
then "Firmware Download".
Firmware download
In the CAN FW folder there are all current Firmware ver-
sions of all axes, tables etc.
Legend
1. The system checks this folder, to see whether there
is a newer version of the firmware for the respective
axis, table etc.. If there exist a new firmware version,
this new version will be offered and could be down-
loaded for example to the star- axis.
2. You can also copy a new firmware version manually
into the CAN FW folder. Click on Copy firmware file to
pool. An Explorer menu will open, in which you can
directly copy the new firmware version from a USB
stick etc. into the CAN FW folder. The firmware ver-
sion you selected will now be available in the selec-
tion menu (see item (1)).
CAUTION
TBS servo for the star axis of the DLM3 head.