SIPLACE D4-D4i 工程师手册_EN.pdf - 第81页
Service Work 4.3.2 Cutter Component Handling Service Manual SIPLACE D4/D4i 81 ▪ Mounting plate [0031273 1-01] ▪ 2 large parallel clamps (or mou nting plate, see above ) ▪ Flat, sturdy work bench to f aste n the r emoved …
Service Work
Component Handling 4.3.2 Cutter
80 Service Manual SIPLACE D4/D4i
► After exchanging the cable for the changeover table and/or the communications unit:
Note the DANGER text regarding the SITEST program.
Load the SITEST program and check the changeover table functions.
► Exit the SITEST program.
► Start the placement process.
4.3.2
4.3.2 Cutter
Cutter
4.3.2.1
4.3.2.1 Safety Instructions
Safety Instructions
4.3.2.2
4.3.2.2 Parts
Parts
All spare parts, plus the corresponding diagrams and article numbers, can be found in the D4 spare parts
catalogue.
See also
4.3.2.4 Overview of Cutter [ ➙ 82]
4.3.2.3
4.3.2.3 Tools, Expendable Materials, Documentation
Tools, Expendable Materials, Documentation
▪ Thick protective gloves
▪ Set of socket wrenches, cross-slotted screwdriver size 4
▪ Open-end wrench, width across flats 10; 1
▪ Torque wrench, Diagonal cutter, Sliding caliper
▪ Feeler gauge: 0.05mm; 1.0mm; 1.5mm; 2.0mm; 2.50 mm
▪ Straight-edge (for check of tape deflector)
DANGER
The safety instructions in the chapter "Operational Safety" in the operating manual and this ser-
vice manual take priority.
The machine is supplied with
219/380 V +/- 5% or
230/400 V +/- 5% or
239/415 V +/- 5% or
117/204 V +/- 5% or
133/230 V +/- 5%,
50/60 Hz mains voltage.
Inside the machine base this is true even while the master switch is turned off.
► The machine has to be switched OFF and disconnected from the line before you perform
any work in the area of the cutter.
► In addition, the compressed air supply must be turned off at the main valve of the com-
pressed air unit in the machine base and the compressed air lines must be bled by actuating
the needle valve on the compressed air unit.
WARNING
► Wear appropriately thick protective gloves when working near the blades/the tape deflector!
► There is a high risk of injury from stationary blades and moveable blades and from the tape
deflector of the cutter, even when the machine has been turned off!
NOTICE
This manual applies for the pneumatic cutter version 04 and the corresponding empty tape duct
version 03.
Version 04 of the cutter contains, for example, a tape deflector for the tapes, which is fitted
above the moveable blades.
Service Work
4.3.2 Cutter Component Handling
Service Manual SIPLACE D4/D4i 81
▪ Mounting plate [00312731-01]
▪ 2 large parallel clamps (or mounting plate, see above)
▪ Flat, sturdy work bench to fasten the removed cutter (or mounting plate, see above)
▪ Loctite No. 234 [00334892-01]
▪ Molykote paste 250 g [02100335-01] (recommended) or ISOFLEX TOPAS NCA 52 tube 50g
[00330850-01]
▪ Water-insoluble, fine-tip marker and
▪ a dry and clean cloth
▪ Current SIPLACE D4 spare parts catalogue and SIPLACE D4 circuit diagrams
▪ SITEST program and current SITEST operating manual
See also
5 Measuring Equipment and Tools [ ➙ 189]
Service Work
Component Handling 4.3.2 Cutter
82 Service Manual SIPLACE D4/D4i
4.3.2.4
4.3.2.4 Overview of Cutter
Overview of Cutter
Overview: Removing and Installing the Cover Plate and the Tape Deflector
Legend
1 Cover plate 10 Screws to fasten the tape deflector: 1 coun-
tersunk screw each -> do not loosen!
2 Cover plate holder, left 11 Holddowns (at left and right) with spacers
inserted underneath them
3 Cover plate holder, right
4 Screws to fasten the cover plate holder:
2 hexagon socket head screws M4 x 8 DIN
84 or 2 countersunk screws R M4 x 6 DIN
965 each
12 Deflector plate
13 Screws to fasten the deflector plate: 4
socket hex head cap screws M4 x 8
5 Screws to fasten the cover plate (incl. tape
deflector) -> do not loosen!
14 Screws to fasten the cutter on the machine
base
4 socket hex head cap screws M 6 x 25 *)
6 Tape deflector (with moveable blade un-
derneath) 15 Any disks or plates installed underneath
7 Tape deflector holder, left 16 Stationary blade
8 Tape deflector holder, right 17 Rubber-metal vibration damper
9 Screws to fasten the tape deflector holders:
2 socket hex head cap screws M4 x 35
each on the left and right
18 Any disks and spring washers installed un-
derneath
CAUTION
Tighten the screws to the correct torque.