00193688-06_Installation SIPLACE Explorer2.1_EN.pdf - 第11页

Installation and Configuration Guide SIPLACE Explorer 1 Introduction Edition 11/2006 EN 1.3 Additional Remarks 11 1.3 Additional Remarks SIPLACE Explorer V ersion 2.1 has the following restrictions: 1 – Factory Layo ut: …

1 Introduction Installation and Configuration Guide SIPLACE Explorer

1.2 System Requirements Edition 11/2006 EN

1.2.3 Supported Data Sources

SIPLACE Explorer V2.1 supports data from the following SIPLACE products: 1

– OIS 4.1, SIS 4.1, SIPLACE Pro 4.1

– OIS 4.0, SIS 4.0, SIPLACE Pro 4.0

– OIS 3.1, SIS 3.1, SIPLACE Pro 3.2

The following versions are supported but if problems should occur, you will need to update these

versions to those shown above. 1

– OIS2.4 SP1, SIS 1.2 SP1, SIPLACE Pro 2.1 SP2

SIPLACE Explorer V2.1 supports data from the following station software versions: 1

– SW 603.01

– SW 602.01

– SW 601.03 SP 2

– SW 601.03 SP 1

– SW 505.04

– SW 505.03 SP 1

– SW 407.04 SP 1

– SW 408.01

The following version is supported but if problems should occur, you will need to update it to the

version shown above. 1

– SW 503.04 SP 2, this version is only suitable if an update to SW 505.03 SP 1 is not possible

due to hardware restrictions.

NOTE

If you want to use the station software 505.03 SP1 or 505.04 along with the transport option

Synchronous double conveyor, you must install the patch:

- 505.03 SP1: 505.03 SP1 Patch OIS sync. DC

- 505.04: 505.04 Hotfix 1 1

Installation and Configuration Guide SIPLACE Explorer 1 Introduction

Edition 11/2006 EN 1.3 Additional Remarks

1.3 Additional Remarks

SIPLACE Explorer Version 2.1 has the following restrictions: 1

– Factory Layout:

A SIPLACE Explorer host (the computer on which SIPLACE Explorer "Runtime Environment"

is installed) can monitor five production lines with up to 20 stations.

– Single Line Layout

A SIPLACE Explorer host (the computer on which SIPLACE Explorer "Runtime Environment"

is installed) can monitor one production line with up to 7 stations.

– From SIPLACE Explorer Version 2.0 SP1, the station GEM interface will no longer be sup-

ported i.e. data can not be recorded via the GEM interface with SIPLACE Explorer Version 2.1

or higher. If you need support for the GEM interface, please contact the SIPLACE Hotline.

– The system time on the connected machines and that belonging to the SIPLACE Explorer must

be synchronized. SIPLACE machines require the installation of TimeSync, which is included

on the Support Media CD provided with the delivery.

– The standard SIPLACE Explorer 2.1 delivery package includes support tools for SIPLACE ma-

chines. This includes all the machines listed in the "Software Version Description SIPLACE Ex-

plorer 2.1, Art. No. 00193690-05.

Support for other equipment, such as screen printers or reflow ovens is not part of the standard

SIPLACE Explorer product package.

If you want to monitor screen printers and reflow ovens with SIPLACE Explorer, this will need

to be realized as a customer-specific project. 1

– A special OIS state model has been realized in SIPLACE OIS. In SIPLACE Explorer, this OIS

state model is mapped onto the SIPLACE Explorer state model which corresponds to the SEMI

E10 state model. This may lead to deviations in the states and state periods shown for OIS and

SIPLACE Explorer. A direct comparison is therefore not possible.

– The following restriction applies to platform I (S20, S23, F4, F5, F5HM) stations with dual con-

veyors:

The page Production Summary will display Unknown in the Current Recipe List table for

the 2nd conveyor lane. 1

Reason:

Platform I stations are unable to produce different recipes, even with dual conveyors. There-

fore, only one recipe will be loaded for the SIPLACE line. This recipe will then only be assigned

to conveyor lane I by SIPLACE Explorer. 1

– The following restrictions apply to the SMA pages listed below, if no boards are placed at the

last station in the production line:

1 Introduction Installation and Configuration Guide SIPLACE Explorer

1.3 Additional Remarks Edition 11/2006 EN

– The page Production Summary will not update the values in the column Lot Progress of

the table Lot Progress, if the last station in the production line does not have any place-

ment contents for the recipe currently defined. In this case, the last station will conveyor the

boards through without placement. The column Lot Progress will continue to show the

name of the last recipe which had placement contents at the last station.

– Machine Navigator:

OLE value will not be shown (N/A).

– OLE / OEE Overview:

Overall Line Efficiency diagram: Values for OLE, performance and availability will not be

shown correctly.

Overall Equipment Efficiency by station diagram: station data is not shown correctly for

stations which do not place boards.

– OEE Analysis:

Table: values for performance and availability will not be shown correctly for lines and sta-

tions which do not place boards.

Overall Equipment Efficiency diagram - comparison diagram: Values for OLE, perfor-

mance and availability will not be shown correctly for the line.

– Factory Overview:

The following values will not be shown correctly or will not be updated:

OLE, Current Recipe/ Job, Last Recipe Change, Completed, Lot Progress, Average Takt

Time.