4OM-1733-005w_F8.pdf - 第53页

Contents Cont-4 Page 4OM-1733 1403-005 4.1 1.3 Nozzle Stocker Sliding Section ...................................... 1-4-55 4.12 Control Box Section ................................................................ 1-4-56…

100%1 / 153
Contents
Cont-3
Page
4OM-1733
1403-005
4.6 Cutter Section .........................................................................1- 4- 20
4.6.1 Cutter Unit (Four Locations) Oiling ................................1- 4- 21
4.6.2 Cutter Unit Inside Oiling .................................................1- 4- 22
4.7 Head Section ..........................................................................1- 4- 23
4.7.1 Nozzle Up/Down Ball Screw (NL-axis)
Cleaning and Oiling .........1- 4- 26
4.7.2 Linear Measure (Light Projector and Receiver)
Cleaning .........1- 4- 27
4.7.3 Diffusion Plate Cleaning ................................................1- 4- 28
4.7.4 Center Spline Oiling .......................................................1- 4- 29
4.7.5 Cam Follower Cleaning and Oiling ................................1- 4- 30
4.7.6 Nozzle Change Cam Surface (Upper)
Cleaning and Oiling ........1- 4- 31
4.7.7 Vacuum Filter Change ...................................................1- 4- 32
4.7.8 Head U/D Ball Screw (HL Axis)
Cleaning and Oiling ........1- 4- 33
4.7.9 Head U/D Linear Guide (HL Axis)
Cleaning and Oiling ........1- 4- 34
4.8 X/Y Beam Section ...................................................................1- 4- 35
4.8.1 X-axis Linear Guide Check ............................................1- 4- 37
4.8.2 X-axis Linear Guide Cleaning and Oiling .......................1- 4- 38
4.8.3 Y-axis Linear Guide Check ............................................1- 4- 39
4.8.4 Y-axis Linear Guide Cleaning and Oiling .......................1- 4- 40
4.8.5 Y-axis Cable Side Cleaning and Oiling ..........................1- 4- 41
4.8.6 Y-axis Cable Fixing Location Check ..............................1- 4- 42
4.8.7 Y-axis Linear Encoder Scale-Tape Cleaning .................1- 4- 42
4.9 PCB Positioning Section .........................................................1- 4- 43
4.9.1 Backup Table Upper Surface Cleaning .......................... 1- 4- 44
4.9.2 Ball Screw Cleaning and Oiling .....................................1- 4- 45
4.9.3 Ball Screw Spline Cleaning and Oiling ..........................1- 4- 46
4.10 Conveyor Section ...................................................................1- 4- 47
4.10.1 Linear Guide Cleaning and Oiling ..................................1- 4- 49
4.10.2 Support Pin Detection Sensor Cleaning ........................1- 4- 50
4.10.3 PCB Detection Sensor Cleaning ...................................1- 4- 51
4.11 Nozzle Stocker Section ...........................................................1- 4- 52
4.11.1 Shutter Flange Pin Sliding Section ................................1- 4- 53
4.11.2 Nozzle Storage Section .................................................1- 4- 54
Contents
Cont-4
Page
4OM-1733
1403-005
4.11.3 Nozzle Stocker Sliding Section ...................................... 1-4-55
4.12 Control Box Section ................................................................1-4-56
4.12.1 Filter Cleaning ...............................................................1-4-57
4.13 Ventilating Fans Section .........................................................1-4-58
4.13.1 Ventilating Fan Cleaning ................................................1-4-59
4.13.2 Ventilating Fan (Filter) Cleaning ....................................1-4-60
5. Maintenance Method ......................................................................1-5-1
5.1 Cleaning Method of Vacuum Nozzles .....................................1-5-2
5.2 Method of detaching vacuum nozzle ......................................1-5-3
5.3 Nozzle Filter Removal Procedure ...........................................1-5-4
5.4 Method of Blow air ..................................................................1-5-5
5.5 Cleaning of high-speed nozzle hole part with pin gauge ........1-5-6
5.6 Nozzle Filter Insertion Procedure ...........................................1-5-9
6. Use Procedure of Diffusion Plate Setup Jig ....................................1-6-1
7. Consumables and Servicing Parts ..................................................1-7-1
7.1 List of Consumables ...............................................................1-7-1
7.2 List of Servicing Parts .............................................................1-7-2
4OM-1733
1208-002 1-A
Chapter 1
Maintenance
In this chapter, all about maintenance are described.
1. Outline of Maintenance
2. Maintenance Check List
3. Maintenance Spots
4. Inspection, Cleaning, and Lubrication Spots
5. Maintenance Method
6. Use Procedure of Diffusion Plate Setup Jig
7. Consumables and Servicing Parts