4OM-1733-005w_F8.pdf - 第64页
4OM-1733 1-1-9 T able 4A1-6 Device Name Inspection Cleaning, and Lubricating Spots Work Maintenance Cycle Daily Weekly Monthly Every 3 Months Every 6 Months Y early Every 2 years 4.6 Feeder Cart Section (Cutter Section) …
4OM-1733
1-1-8
1.3 Items for Periodic Maintenance
The items (inspection, cleaning, lubrication, etc.) that require periodic
maintenance are classied and described based on each individual devices.
Reference
Refer to "2. Maintenance Check List" in "Chapter 1" for the maintenance based
on frequency of use.
Notice
The * -marks represent that the items require maintenance only for the
rsttime.
Followthe○-markedmaintenancecycleforthesubsequentuse.
Table 4A1-5
Device Name
Inspection Cleaning,
and Lubricating Spots
Work
Maintenance Cycle
Daily Weekly
Monthly
Every
3 Months
Every
6 Months
Yearly
Every
2 years
4.1 Air Source
Main Air Pressure
Inspection
○
Air Blowing Pressure
Inspection
○
Z Clamp Pressure
Inspection
○
Drain
Cleaning
○
Filter
Cleaning
○
4.2 Vacuum System
Vacuum Pressure
Inspection
○
Filter
Cleaning
○
4.3 Component
Recognition
Camera Section
Component Recognition
Camera
Cleaning
○
Component Storage Box
Cleaning
○
Fiducial Mark
Cleaning
○
4.4 Feeder Base
Driving Section
Worm Gear
Lubrication
○
4.5 Feeder Cart
Section
Groove on Feeder Base
Cleaning
○
Upper Surface of Feeder
Base
Cleaning
○
Real Box
Cleaning
○
Scrap Box
Cleaning
○
1211-003
1.3 Items for Periodic Maintenance
4OM-1733
1-1-9
Table 4A1-6
Device Name
Inspection Cleaning,
and Lubricating Spots
Work
Maintenance Cycle
Daily Weekly
Monthly
Every
3 Months
Every
6 Months
Yearly
Every
2 years
4.6
Feeder Cart Section
(Cutter Section)
Cutter Unit
Cleaning
○
OILES Guide
Lubrication
○
Movable Blade
Change
○
Fixed Blade
Change
○
OILES Guide
Change
○
4.7 Head Section
High Speed Head
Nozzle U/D Ball Screw
(NL Axis)
Cleaning,
Lubrication
○
Diffusion Plate
Cleaning
○
Linear Measure Sensor
(Light Emitter and
Receiver)
Cleaning
○
Nozzle Change Cam Face
(Lower Side)
Cleaning,
Lubrication
○
Center Spline
Lubrication
○
Cam Follower
Cleaning,
Lubrication
○
Vacuum Filter
Change
○
Nozzle Filter
Change
○
Head U/D Ball Screw
(HL Axis)
Cleaning,
Lubrication
○
Head U/D Linear Guide
(HL Axis)
Cleaning,
Lubrication
*
○
Note
The head up/down ball screw (HL-axis) and the head up/down linear guide
(HL-axis) are applicable only to the high-speed head SIGMA F8 (HL).
1403-005
1.3 Items for Periodic Maintenance
4OM-1733
1-1-10
Table 4A1-7
Device Name
Inspection Cleaning,
and Lubricating Spots
Work
Maintenance Cycle
Daily Weekly
Monthly
Every
3 Months
Every
6 Months
Yearly
Every
2 years
4.8 X/Y Beam Section
X-Axis Linear Guide
Inspection
○
X-Axis Linear Guide
Cleaning,
Lubrication
*
○
Y-Axis Linear Guide
Inspection
○
Y-Axis Linear Guide
Cleaning,
Lubrication
*
○
X-Axis Cable Side Face
Cleaning,
Lubrication
○
X-Axis Cable Fixing
Places
Inspection
○
X-Axis Linear Scale
Cleaning
○
Y-Axis Cable Side Face
Cleaning,
Lubrication
○
Y-Axis Cable Fixing
Places
Inspection
○
Y-Axis Linear Scale
Cleaning
○
4.9 PCB Positioning
Section
Upper Surface of Backup
Table
Cleaning
○
Ball Screw
Cleaning,
Lubrication
*
○
Ball Screw Spline
Cleaning,
Lubrication
○
4.10
Conveyor Section
Linear Guide
Cleaning,
Lubrication
*
○
Support Pin Detection
Sensors
Cleaning,
Lubrication
○
PCB Detection Sensor
Cleaning
○
4.11 Nozzle Stocker
Section
Nozzle Storage Section
Cleaning
○
Nozzle Stocker Sliding
Area
Cleaning,
Lubrication
○
Shutter Flange Pin Sliding
Section
Cleaning,
Lubrication
○
4.12 Control Box
Section
Filter
Cleaning
○
Note
The item "Ball Screw Spline (4.9 PCB Positioning Unit)" is for the system
where the Y510mm Single Transfer Unit (Option) has been mounted.
1403-004
1.3 Items for Periodic Maintenance