4OM-1733-005w_F8.pdf - 第63页

4OM-1733 1-1-8 1.3 Items for Periodic Maintenance The items (inspection, cleaning, lubrication, etc.) that require periodic maintenance are classied and described based on each individual devices. Reference Refer to &qu…

100%1 / 153
4OM-1733
1-1-7
(4) Syringe
Maker: TERUMO
This gun can be used for two types of greases.
Use the syringes and the nozzle properly.
Two Types of Greases : DAPHNE EPONEX GREASE No. 1
MOLYNOC GREASE AP1
Appearance
Fig. 4A1-5
Table 4A1-4
Standard Shape Part No. Remarks
Syringe
KYB-M382K-00
228A0171
Maker : TERUMO
10ml SS-10-LZ
Nozzle No.18
(Color : Green)
---
216G0451
Maker : SAN-EI TECH
Inside Diameter :
f
0.84
Tapered Nozzle #5118TT-B
Nozzle No.19
(Color : Brown)
KYB-M380X-00
0916D108
Maker : NIPRO
Inside Diameter :
f
0.79
Length : 65 mm Flat End
1208-002
1.2 Preparation for Maintenance
4OM-1733
1-1-8
1.3 Items for Periodic Maintenance
The items (inspection, cleaning, lubrication, etc.) that require periodic
maintenance are classied and described based on each individual devices.
Reference
Refer to "2. Maintenance Check List" in "Chapter 1" for the maintenance based
on frequency of use.
Notice
The * -marks represent that the items require maintenance only for the
rsttime.
Followthe○-markedmaintenancecycleforthesubsequentuse.
Table 4A1-5
Device Name
Inspection Cleaning,
and Lubricating Spots
Work
Maintenance Cycle
Daily Weekly
Monthly
Every
3 Months
Every
6 Months
Yearly
Every
2 years
4.1 Air Source
Main Air Pressure
Inspection
○
Air Blowing Pressure
Inspection
○
Z Clamp Pressure
Inspection
○
Drain
Cleaning
○
Filter
Cleaning
○
4.2 Vacuum System
Vacuum Pressure
Inspection
○
Filter
Cleaning
○
4.3 Component
Recognition
Camera Section
Component Recognition
Camera
Cleaning
○
Component Storage Box
Cleaning
○
Fiducial Mark
Cleaning
○
4.4 Feeder Base
Driving Section
Worm Gear
Lubrication
○
4.5 Feeder Cart
Section
Groove on Feeder Base
Cleaning
○
Upper Surface of Feeder
Base
Cleaning
○
Real Box
Cleaning
○
Scrap Box
Cleaning
○
1211-003
1.3 Items for Periodic Maintenance
4OM-1733
1-1-9
Table 4A1-6
Device Name
Inspection Cleaning,
and Lubricating Spots
Work
Maintenance Cycle
Daily Weekly
Monthly
Every
3 Months
Every
6 Months
Yearly
Every
2 years
4.6
Feeder Cart Section
(Cutter Section)
Cutter Unit
Cleaning
○
OILES Guide
Lubrication
○
Movable Blade
Change
○
Fixed Blade
Change
○
OILES Guide
Change
○
4.7 Head Section
High Speed Head
Nozzle U/D Ball Screw
(NL Axis)
Cleaning,
Lubrication
○
Diffusion Plate
Cleaning
○
Linear Measure Sensor
(Light Emitter and
Receiver)
Cleaning
○
Nozzle Change Cam Face
(Lower Side)
Cleaning,
Lubrication
○
Center Spline
Lubrication
○
Cam Follower
Cleaning,
Lubrication
○
Vacuum Filter
Change
○
Nozzle Filter
Change
○
Head U/D Ball Screw
(HL Axis)
Cleaning,
Lubrication
○
Head U/D Linear Guide
(HL Axis)
Cleaning,
Lubrication
*
○
Note
The head up/down ball screw (HL-axis) and the head up/down linear guide
(HL-axis) are applicable only to the high-speed head SIGMA F8 (HL).
1403-005
1.3 Items for Periodic Maintenance