ServiceInstruction_Vision XP.pdf - 第138页

Seite 134 V ISION XP+ V AC Bildverzeichnis Operating Instructions V ersion 1.5 Gas take-off p oint Fig. 2-87 53 Heater Param eters Fig. 3-3 67 Inserting the nozzle holder Fig. 2-13 19 Lifting off the Grate Fig. 2-86 52 L…

100%1 / 142
VISION XP+ VAC Page 133
Page
List of Figures
Operating Instructions
Version 1.5
List of Figures
Volume flow control, cooling section parameter Fig. 3-14 98
Additional cleaning chute Fig. 2-34 28
Adjusting the Center Support Fig. 3-24 114
Adjusting the Conveyor Side Panel Fig. 3-23 112
Alarm Configuration Fig. 3-9 81
Bottom Curtains Fig. 2-17 22
Chain lubricating pumps with two and one outlet Fig. 2-98 57
Chain Lubricator Fig. 3-8 80
Chain oiler - MU (bottom) Fig. 2-100 58
Changing to adjusting plane Fig. 3-17 103
Check the chain slack Fig. 2-52 37
Checking the Water Fill-Level Fig. 2-67 45
Cleaning of coated nozzle fields Fig. 2-14 20
Cleaning of coated nozzle fields Fig. 2-15 20
cleaning of oven station Fig. 2-4 16
cleaning of oven station Fig. 2-5 16
Cleaning the Fan Impeller Fig. 2-41 30
Cleaning the gas take-off point Fig. 2-88 53
Cleaning the Guide Rails Fig. 2-16 21
Cleaning the Interior Fig. 2-3 15
Cleaning the Process Chamber Seal Fig. 2-20 23
Cleaning the Sensors Fig. 2-101 59
Compressed Air and Nitrogen Unit Fig. 3-32 121
Condensate Trap Layout Fig. 2-70 46
Condensate Trap Fig. 2-69 46
Configuration Activ Energy Meters Fig. 3-22 109
Control Cabinet 1 Fig. 2-102 60
Control Cabinet 2 Fig. 2-103 60
Conveyor Adjustment – Parameters Fig. 3-7 77
Conveyor Drive Parameters Fig. 3-6 75
Coolant Water Regulation Fig. 3-31 120
Cover for Suction Chamber Fig. 2-31 27
Disconnect power supply Fig. 2-36 29
Exchange activated carbon Fig. 2-93 55
Exchange activated carbon Fig. 2-94 55
Exchange activated carbon Fig. 2-95 55
Exchange activated carbon Fig. 2-96 56
Exchange activated carbon Fig. 2-97 56
Exhaust Air Differential Pressure Gauge Fig. 3-28 117
Extracting the nozzle holder Fig. 2-10 18
Extracting the nozzle holder Fig. 2-11 18
Extracting the nozzle holder Fig. 2-12 18
Fan Impeller Fig. 2-33 27
Fan Parameters Fig. 3-11 93
Fans Parameter (example) Fig. 3-33 127
Filter Vacuum pump Fig. 2-57 40
Filter Vacuum pump Fig. 2-58 40
Filter Vacuum pump Fig. 2-59 40
Flux Management Parameters Fig. 3-5 74
Frequency Converter Parameters Fig. 3-10 84
Seite 134 VISION XP+ VAC
Bildverzeichnis
Operating Instructions
Version 1.5
Gas take-off point Fig. 2-87 53
Heater Parameters Fig. 3-3 67
Inserting the nozzle holder Fig. 2-13 19
Lifting off the Grate Fig. 2-86 52
Lifting the Filter Housing Fig. 2-66 44
Lifting the Filter Out of the Housing Fig. 2-65 44
Loosening the Nuts Fig. 2-84 52
Lower nozzle field Fig. 2-37 29
N2 Parameters Fig. 3-12 94
Nozzle holder Fig. 2-9 18
Pressure Switch Adjusting Screw Fig. 3-29 118
Protective clothing Fig. 1-1 6
Pulling Out the Catch Pan Fig. 2-73 48
Pulling Out the Cooler Unit Fig. 2-74 49
Pulling Out the Cooler Unit Fig. 2-77 50
Pulling Out the Filter Housing Fig. 2-64 44
Pulling Out the Filter unit F9 Fig. 2-78 50
Pulling Out the Filter Fig. 2-75 49
Pulling Out the Gauze Filter Fig. 2-71 47
Push the clips up with prying tool Fig. 2-19 22
Pyrolysis Unit Fig. 2-81 51
Removing the Insulation Fig. 2-83 52
Removing the Insulation Fig. 2-85 52
Replacing the Process Chamber Seals Fig. 2-21 24
Replacing the Process Chamber Seals Fig. 2-23 24
Sealing the gas take-off point Fig. 2-89 53
Sensors for the vacuum chamber Fig. 2-53 38
Sensors for the vacuum chamber Fig. 2-54 38
Service Settings Fig. 3-2 64
Setup Fig. 3-21 108
Sheet Metal Cover on Impeller Fig. 2-32 27
Terminal X1 Fig. 3-26 115
The Service Menu Fig. 3-1 63
Top curtains (2-part) Fig. 2-18 22
Transport chain oiler (top) Fig. 2-99 58
Trapped heat cooler Fig. 2-40 30
Trapped heat cooler Fig. 2-39 30
Ultrasonic senor Fig. 3-25 115
Unlatch, remove the cooling module Fig. 2-38 29
Unscrew the filter casing Fig. 2-90 54
Unscrew the filter insert Fig. 2-91 54
Unscrewing the Door Fig. 2-82 51
Vacuum chamber service Fig. 3-15 100
vacuum chamber Fig. 2-47 33
Vacuum parameters Fig. 3-16 102
vakuum pump Fig. 2-60 41
Watchdog Parameters Fig. 3-4 72
Water Flow Rate Fig. 3-30 119
X- terminal and SPS Fig. 3-27 115
VISION XP+ VAC Page 135
List of Tables
Service Instructions
Version 1.5
List of Tables
Page
Adjustment Default Values Tab. 3-5 123
Alarm Configuration (default values) Tab. 3-6 125
Alarm Types Tab. 3-1 83
Chain Lubricator (default values) Tab. 3-11 129
Conveyor Drive Parameter (default values) Tab. 3-10 129
Default Value Consumption Parameters Tab. 3-14 131
Default Values Filter F9 Parameter Tab. 3-15 131
Default Values Nitrogen control Tab. 3-12 130
Default Values Nitrogen control Tab. 3-13 130
Fans Monitoring (default values) Tab. 3-8 127
Frequency Converter Parameter (default values) Tab. 3-7 126
Interface (default values) Tab. 3-9 128
Maintenance Schedule Nitro Tab. 2-1 13
Parameter Mitsubishi FR-D 700 Tab. 3-2 86
Revision Levels for Service Instructions Tab. 1-1 3
Siemens Type Micromaster MM420 – Parameters Tab. 3-4 91