HS50_advance_level 1_20200522_221201 (1).pdf - 第135页
Studen t Guide HS-50 A dvanced I 06/200 2 Edition 5 DLM1 C&P Head 43 ➠ Care fu lly pu sh the camera against the revolv er head u ntil the camera pl inth is lyin g flat on the contact surfaces on the front part of t h…
06/2002 Edition Student Guide HS-50 Advanced I
5 DLM1 C&P Head
42
5
Fig. 5.4 - 7 Replacing the component camera
(1) 24x24 component camera
(2) "Component illumination controller" board
(3) 4 x M4x10 hexagon-socket head screws
(4) 2 parallel pins
X3 Socket 5
5
Student Guide HS-50 Advanced I 06/2002 Edition
5 DLM1 C&P Head
43
➠ Carefully push the camera against the revolver head until the camera plinth is lying flat on the
contact surfaces on the front part of the revolver head.
➠ Use the four M4x10 hexagon socket-head screws to fix the camera in place (see item 6 in Fig.
5.4 - 7
).
➠ Connect the ribbon cable to socket X3 on the "component illumination" board (item X3 in
Fig. 5.4 - 7
).
➠ Fit the front part of the revolver head as described in section 5.4.3.3, page 5 - 39.
➠ Fix the head cover in place.
5.4.4.5 Settings
➠ Start the placement system.
➠ Use the SITEST program to calibrate the revolver head.
5.4.5 Removal of star
5.4.5.1 Tools and equipment
– Set of DIN 911 Allen keys
– Gauge for the star (revolver head / DLM1), article number 00326164-01
– Power pack for the revolver head / DLM1, article number 00353277-01
– Tray for transporting the revolver head
– Laboratory gloves
5.4.5.2 Parts
Star, mounted / DLM1, article number 00341181-01 5
5.4.5.3 Dismantling the star
➠ Dismantle the front part of the revolver head as described in section 5.4.3, page - 36 onwards.
➠ Place the front part of the revolver head on the tray.
PLEASE NOTE:
Wear laboratory gloves when you remove the sleeves from the star. 5
➠ Remove all the sleeves (item 1 in Fig. 5.4 - 8) and place them in the sleeve box or on a soft,
clean surface.
➠ Loosen the three M3x8 hexagon socket head screws (item 5 in Fig. 5.4 - 8).
➠ Raise the star slightly.
➠ Use a rotary movement to lift the star up and off.
06/2002 Edition Student Guide HS-50 Advanced I
5 DLM1 C&P Head
44
5
Abb. 5.4 - 8 Replacing the star
(1) Sleeve
(2) Star, mounted / DLM1
(3) Star drive
(4) Front part of revolver head
(5) M3x8 hexagon socket head screws, 3x
(6) Segment
(7) Raceway
5.4.5.4 Fitting the star
PLEASE NOTE:
Remove any remaining sleeves before fitting the star.
Wear laboratory gloves when removing the sleeves. 5
➠ Push all the segments (item. 6 in Fig. 5.4 - 8) slightly outwards.
➠ Insert small Allen keys (e.g. size 2) into the holes for the star fixing screws (item 5 in Fig.
5.4 - 8
).
➠ Hold the star over the star drive shaft (item 3 in Fig. 5.4 - 8) so that the Allen keys slide into the
threaded holes in the star drive.