00198150-02_SM_TX_en.pdf - 第207页
8 Placement Heads and Stationary Cameras 8.3 Replacing the SIPLACE CPP/M Head Service Manual SIPLACE TX Series 06/2017 207 Fig.281: Component sensor protective cap ► Fit the protective cap onto the component sensor for …
8 Placement Heads and Stationary Cameras
8.3 Replacing the SIPLACE CPP/M Head
206 Service Manual SIPLACE TX Series 06/2017
8.3 Replacing the SIPLACE CPP/M Head
NOTICE
Vacuum test
► If required, perform a vacuum test before removing the placement head.
Read the "Service manual Vacuum test at C&P placement head" [DE+EN:
00196101‑xx] for this.
NOTICE
Fast Head Exchange (FHE)
► Observe the instructions in section 8.1 "Fast Head Exchange" [}197] when exchan-
ging a head.
Parts, equipment and tools
●
SIPLACE CPP placement head [03053528Sxx] (without camera)
●
SIPLACE CPP M placement head [03153719Sxx] (without camera)
●
Torx screwdriver ESD 1.0-5.0 Nm [03078400-xx]
●
Extension/straight TX20 [03073256-xx]
●
Bit holder for TorqueVario screwdriver [03078706-xx]
●
Component sensor protective cap [03080984-xx]
●
Calibration tool version 3 [03010565-xx]
●
Calibration tool version SST23 [03034148-xx]
For additional work to the placement head:
●
Head mount [03056231‑xx]
●
Service manual "SIPLACE CPP head" [DE:00197462‑xx] [EN:00197463‑xx]
Overview
Fig.280: Overview (example of CPP head shown)
1 to 4: Fixture holes (two each, depends on installa-
tion height).
5: Dowel holes for the index pins
6: Component camera
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation. Observe the instructions in section 1.2 "Preparatory Work..." [}15].
CAUTION
Take great care when dismantling the placement head!
The component sensor prisms, underneath the placement head, could be damaged.
► Never place the placement head down on the component sensor.
8 Placement Heads and Stationary Cameras
8.3 Replacing the SIPLACE CPP/M Head
Service Manual SIPLACE TX Series 06/2017 207
Fig.281: Component sensor protective cap
► Fit the protective cap onto the component sensor
for the placement head.
Fig.282: Connections
► Unplug the pneumatic connections(1) from the
placement head. You may want to mark the posi-
tions to make clear assignment easier later on.
► Disconnect the flat ribbon cables(3) from the in-
termediate distributor(2).
Fig.283: Cables
► Push the button(1) to unplug the cable, open the
clamps on both sides of connector to unplug the
flat ribbon cable(2).
► Remove all four screws fastening the head with a long Torx screwdriver.
► Carefully lift the head out of the locating pins on the head plate and from the hook.
► Placing the head into the head transport box
8 Placement Heads and Stationary Cameras
8.3 Replacing the SIPLACE CPP/M Head
208 Service Manual SIPLACE TX Series 06/2017
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following in-
structions:
CAUTION
Installation instructions
► If you replace the head without the component camera, you will need to fit the old
camera onto the new head. Read the service manual for your placement head for
more information.
► Observe the correct installation height of the head (top or bottom position, see 8.3.1
"Preparing the CPP Head for the Installation Height" [}209])!
► Make sure that the assembly position on the head plate is correct.
► Tighten the four fastening screws with a torque of 2.7Nm.
► Make sure that the flat ribbon cable is run correctly to the head adapter (see below).
Fig.284: Flat ribbon cable
Correct running of flat ribbon cable to head ad-
apter
► Make sure that the flat ribbon cable is run cor-
rectly to the head adapter. In particular, the
cables must lie inside one another at the 90 de-
grees turn(1) and not on top of one another, oth-
erwise the connections on the head adapter
could be easily confused.