00198150-02_SM_TX_en.pdf - 第264页
11 Cutter 11.9 Replacing the Cutter Blades 264 Service Manual SIPLACE TX Series 06/2017 11.9 Replacing the Cutter Blades CAUTION Risk of injury! There is a high risk of injury from the blades and the tape deflector. ► We…
11 Cutter
11.8 Replacing the Short-Stroke Cylinder [03038587-xx]
Service Manual SIPLACE TX Series 06/2017 263
1
3
2
Fig.366: Fitting the short-stroke cylinder
► Fit the proximity switch (1) precisely in the posi-
tion you marked with the permanent marker.
► Place the prepared cylinder into the cutter, in the
correct rotary position of the articulated joint (2).
► Fasten the cylinder in this position, with the two
screws provided(3) (Loctite243).
► Connect the compressed air hoses to the cylinder in the correct allocation.
► Further installation is performed by following the above instructions in the reverse order. Ob-
serve the following instructions:
NOTICE
Installation instructions
► Also observe section 11.7 "Replacing the Articulated Joint on the Short-Stroke Cylin-
der [03000518-xx]" [}259].
► From SW707.1: set the restrictors (see 11.13.1 "Times for Setting the Throttle on the
Cutter (From SW707.1)" [}275]).
See also
2 Times for Setting the Throttle on the Cutter (From SW707.1) [}275]
2 Replacing the Articulated Joint on the Short-Stroke Cylinder [03000518-xx] [}259]
2 Replacing the Cutter on the COT Insert [03066690-xx] [}252]
11 Cutter
11.9 Replacing the Cutter Blades
264 Service Manual SIPLACE TX Series 06/2017
11.9 Replacing the Cutter Blades
CAUTION
Risk of injury!
There is a high risk of injury from the blades and the tape deflector.
► Wear appropriately thick protective gloves!
► Never reach into the cutter from below or into the empty-tape duct from above.
► Make sure that no-one can injure themselves on the cutter after it has been dis-
mantled and placed next to the machine!
Parts, equipment and tools
NOTICE
Turn the blade
The fixed and movable blades have been sharpened on both sides. If one side becomes
blunt, you can rotate the blade by 180 degrees to use the other side.
●
Measurer set aligned (tape cutter HF) [03009259-xx] (fits TX tape cutter, pneumatic
[03066690‑xx])
●
2x blade cover (tape cutter HF) [03000553-xx] (cover for screws of movable blades)
●
2x hexagon socket fillister head screws ISO4762-M5x35-12.9, geomet 321+VL [03057290‑xx]
(screws for movable blade)
●
2x articulated joint (cutter HF) [03000518-xx]
●
2x DIN71412-BM6 [03036943-xx] (lubrication nipple)
Consumables required:
●
Lubricant grease Klüber BEM 34-132 tin 1 kg [00374565-xx] (identical to the lubricant grease
used on the guide carriage of the gantry)
●
Interflon Fin grease [03020782-xx]
●
Loctite 243 [00334892‑xx]
Tools required:
●
Extra protection gloves, leather [00091001-xx]
●
Torx screwdriver ESD 1.0-5.0 Nm [03078400-xx]
●
Torque wrench 2.5 - 25 Nm [00376625-xx]
●
Bit holder for TorqueVario screwdriver [03078706-xx]
●
Socket-head bit size 3-6
●
Fork wrench, size 10
●
Feeler gauge
●
Brush
●
Cloth
●
Two large parallel clamps and a sturdy table with even surface, to clamp down the dismantled
cutter
11 Cutter
11.9 Replacing the Cutter Blades
Service Manual SIPLACE TX Series 06/2017 265
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation. Observe the instructions in section 1.2 "Preparatory Work..." [}15].
► Remove the cutter from the machine.
Replacing the Cutter on the COT Insert [03066690-xx] [}252]
Fig.367: Cover plate
► Remove the screws(2) fastening the top cover
plate(1) and then remove the top cover plate.
Fig.368: Baffle plate
► Remove the two screws(1) at the front side and
five screws(2) at the inner side fastening the
baffle plate.
► Remove the baffle plate unit from the cutter.
Fig.369: Plastic caps
From the bottom side of the cutter you have easy ac-
cess to the plastic cap.
► Remove the plastic caps(1) over the fastening
screws on both sides of the movable blade.
► Remove the two screws.