00198140-01_UM_JTF-ML_TX12_de_en.pdf - 第84页

Setting up and Commissioning Retrofitting in the SIPLACE TX-Series 4.2.1 Scope of Delivery 84 JEDEC Tray Feeder (JTF-ML) SIPLACE JTF-ML a dapter assembly SIPLACE JTF-ML FDK Empty-tape duct, s hort TX assembly Cover assem…

100%1 / 124
Setting up and Commissioning
4.2.1 Scope of Delivery Configuration and Restrictions
JEDEC Tray Feeder (JTF-ML) 83
4
4 Setting up and Commissioning
Setting up and Commissioning
4.1
4.1 Configuration and Restrictions
Configuration and Restrictions
The following requirements and restrictions apply to the SIPLACE JTF-ML:
▪ Assembly is only possible on SIPLACE TX1/TX2 machines.
It is not possible with SIPLACE TX2i machines.
▪ The software version must be 709.0 or higher.
▪ The assembly is only possible at location 1.
▪ The following placement heads are possible:
– CPP_H
– TwinHead
4.2
4.2 Retrofitting in the SIPLACE TX-Series
Retrofitting in the SIPLACE TX-Series
4.2.1
4.2.1 Scope of Delivery
Scope of Delivery
You need the following parts:
▪ SIPLACE JTF-ML (tray feeder module) [00588105-xx]
▪ Changeover table for SIPLACE JTF-ML [00588112-xx]
▪ Assembly kit for SIPLACE JTF-ML [00588106-xx]
This contains:
4.2.1.1
4.2.1.1 Overview of Parts
Overview of Parts
Quantity Designation Item No.
1 SIPLACE JTF-ML adapter assembly 03114835-xx
1 SIPLACE JTF-ML FDK 03110417-xx
1 Empty-tape duct, short TX assembly 03121376-xx
1 JTF cover assembly 03125471-xx
1 Cover assembly for JTF
This contains:
03119382-xx
1 Support frame SP1 for JTF assembly 03114836-xx
1 Cover on output side SP1 assembly TX 03115547-xx
1 Pneumatic connection SIPLACE JTF-ML TX 03133631-xx
1 Mounting support TX-JTF assembly 03136824-xx
SIPLACE JTF-ML (tray feeder module)
Setting up and Commissioning
Retrofitting in the SIPLACE TX-Series 4.2.1 Scope of Delivery
84 JEDEC Tray Feeder (JTF-ML)
SIPLACE JTF-ML adapter assembly
SIPLACE JTF-ML FDK
Empty-tape duct, short TX assembly
Cover assembly for SIPLACE JTF-ML
Consists of:
1. Support frame assembly SP1 for SIPLACE JTF-ML
2. Cover assembly on output side SP1, TX
Mounting support TX-JTF assembly
Setting up and Commissioning
4.2.2 Tools and Equipment Required Retrofitting in the SIPLACE TX-Series
JEDEC Tray Feeder (JTF-ML) 85
4.2.2
4.2.2 Tools and Equipment Required
Tools and Equipment Required
▪ Standard tools
▪ Recommended: Allen key extension, ratchet
▪Hammer
▪Punch
▪ Feeler gauge
▪ Belt tension device
▪ Lifting trolley
▪ Second person
▪ Assembly instructions "Input and Output Conveyor Extension SIPLACE TX" [00198141-xx]
4.2.3
4.2.3 Required Working Time
Required Working Time
The complete installation, including the output conveyor extension, will take approx. four hours.
4.2.4
4.2.4 Preparatory Steps
Preparatory Steps
► Move the component trolley out of the machine.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "2.1.6 Preparatory Work..." [ ➙ 76].
4.2.5
4.2.5 Converting the COT Insert
Converting the COT Insert
TX - Removing the NC
Removing NC 1
► Remove the four screws (1) fastening the nozzle
changer (NC).
Removing NC 2
► Unplug the electrical (1) and pneumatic
connections (2) for the nozzle changer and put the
NC aside.