00195376-05_SM_D1_D1i_D2_D2i_EN.pdf - 第149页
Service Work 4.4.19 Replacing the RSF Digita l Rotary Encoder (DP Axis) [0033 5990-xx] C&P6/12 Head Service Manual SIPLACE D1/D1i/D2/D2i 149 Installation See also 4.4.4 Re placing the I ntermediate Distributor [ …
Service Work
C&P6/12 Head 4.4.18 Replacing the Star Drive
148 Service Manual SIPLACE D1/D1i/D2/D2i
▪ When fitting the star, make sure that the silicone hoses are not pinched and/or damaged.
4.4.18
4.4.18 Replacing the Star Drive
Replacing the Star Drive
Parts, equipment and tools
▪ Star motor assembly DLM1, DLM2 [03020626-xx]
▪ Star motor assembly DLM3, DLM4 [03031187-xx]
Removal
CAUTION!
If the connecting silicone hoses between the valve and
segment are replaced, make sure that they are not dam-
aged by rubbing against one another (2) .
To ensure this, make sure that the silicone hoses have
been cut to the exact length and that they are pushed
onto the respective connection pieces as far as possible
(up to the stopper).
Make sure that the hoses do not touch (1) one another.
Check the distance while pushing all segments all the
way in. Ideally, the distances should all be the same.
1. Star drive, digital (DLM3, DLM4)
2. 4 x M5x16 hexagon socket-head screws
3. Front section of C&P head
(A) Connecting cable for the star drive
► Dismantle the intermediate distributor.
► Dismantle the front part of the C&P head.
► Dismantle the star.
► Loosen the four M5x16 hexagon socket-head screws
(2).
► Lift the star drive off the front part of the C&P head.
A
1
3
2
Service Work
4.4.19 Replacing the RSF Digital Rotary Encoder (DP Axis) [00335990-xx] C&P6/12 Head
Service Manual SIPLACE D1/D1i/D2/D2i 149
Installation
See also
4.4.4 Replacing the Intermediate Distributor [ ➙ 119]
4.4.2 Removal/Installation of Head Front Part [ ➙ 115]
4.4.17 Replacing the Star [ ➙ 144]
6.5.9 Determining the Zero Point Correction for the Star Axis of the C&P Head [ ➙ 238]
4.4.19
4.4.19 Replacing the RSF Digital Rotary Encoder (DP Axis) [00335990-xx]
Replacing the RSF Digital Rotary Encoder (DP Axis) [00335990-xx]
Removal
► Place the star motor onto the front part of the C&P
head, so that the star drive connection cable points to
the position marked (A).
► Fix the star drive in place with the four M5x16 hexa-
gon socket-head screws (2).
► Fit and adjust the star. (See zero point correction.)
► If you are unable to adjust the zero point correction
correctly, loosen the 4 star motor screws and rotate
the star motor in the required direction, within the
tightening tolerance.
► Fit the front part of the C&P head.
A
1
3
2
1. Front section of C&P head
2. RSF digital rotary encoder 12/DLM3
3. 2 x M2.5x8 hexagon socket-head screws
4. RSF board, type 950
5. 2 x M2.5x4 hexagon socket-head screws
6. Plug connector in the slot on the intermediate distrib-
utor
► Dismantle the front part of the C&P head.
► Remove the black blanking cap over the RSF board
(4).
► Remove the plug connector (6) from the slot on the
intermediate distributor.
► Loosen the two M2.5x4 hexagon socket-head screws
(5) for fixing the RSF board.
► Dismantle the handle of the C&P head.
► Loosen the two M2.5x8 hexagon socket-head screws
(3) and remove the digital encoder.
1
6
5
4
3
2
Service Work
C&P6/12 Head 4.4.19 Replacing the RSF Digital Rotary Encoder (DP Axis) [00335990-xx]
150 Service Manual SIPLACE D1/D1i/D2/D2i
Installation
► Insert the new rotary encoder and initially fix loosely
in place with the two M2.5x8 hexagon socket-head
screws (3).
► Fit the handle of the C&P head.
► Insert the sleeve into the star and turn the star, with
the sleeve, until it reaches the rotary encoder.
► Fix the star in this position using the gauge for the
star.
1
6
5
4
3
2