4M184002w_F8S.pdf - 第192页

Error ID Error Name, Description, Cause, and Remedy 421317 Error in the movement of output conveyor Limit sensor(-) of output conveyor was detected No use the function. Please check the driver-axis setting when error is …

Error ID Error Name, Description, Cause, and Remedy

42121e Error in the Movement of positioning Conveyor

Reserved Code

Reserved Function of driver. Please make inquiries when error is detected.

42121f Error in the Movement of positioning Conveyor

System Error on positioning conveyor

System Error of internal driver. Driver error is supposed if this problem happens

frequently.

421301 Error in the movement of output conveyor

Error in the output conveyor

Please transit again after returning P.C.B. position.

Please let me know about error specication(Free Code No.) if Error often

happens.

421302 Error in the movement of output conveyor

Driver alarm of output conveyor

Conrm reset Method of detailed Sub-system error counts of Alarm.

421310 Error in the movement of output conveyor

System setup of output conveyor is not completed.

Driver has not completed the parameter setup yet. It is a situation in which a

correct setup has not been received by Communication Error.

Check the Communication Mode, wiring, Power supply of Driver.

421311 Error in the movement of output conveyor

Zeroing Error of output conveyor

No use the function. Please check the driver-axis setting when error is detected

because there is a possibility of error of driver-axis setting.

421312 Error in the movement of output conveyor

Out-of-Control of output conveyor

No use the function. Please check the driver-axis setting when error is detected

because there is a possibility of error of driver-axis setting.

421313 Error in the movement of output conveyor

Error in motor power voltage of output conveyor

Motor power voltage dropped. Check out the Power supply line(48V Line)

421314 Error in the movement of output conveyor

STP input on output conveyor was detected

STP input is detected. The function to stop motor by Hard signal.

421315 Error in the movement of output conveyor

Over-current on output conveyor

Abnormal current in motor output line was detected. Conrm the motor wiring,

supplying power.

421316 Error in the movement of output conveyor

Limit sensor(+) of output conveyor was detected

No use the function. Please check the driver-axis setting when error is detected

because there is a possibility of error of driver-axis setting.

3.3 Conveyor

4OM-1840

3-3-301604-001

Error ID Error Name, Description, Cause, and Remedy

421317 Error in the movement of output conveyor

Limit sensor(-) of output conveyor was detected

No use the function. Please check the driver-axis setting when error is detected

because there is a possibility of error of driver-axis setting.

421318 Error in the movement of output conveyor

Disconnecting Motor of output conveyor was detected

Disconnection to motor was detected.(Only stop mode)

Check the motor wiring.

421319 Error in the movement of output conveyor

Error in control power voltage of output conveyor

Control power for driver dropped. Check out the Power supply line.(24V Line)

42131a Error in the movement of output conveyor

Reserved Code

Reserved Function of driver. Please make inquiries when error is detected.

42131b Error in the movement of output conveyor

Reserved Code

Reserved Function of driver. Please make inquiries when error is detected.

42131c Error in the movement of output conveyor

Reserved Code

Reserved Function of driver. Please make inquiries when error is detected.

42131d Error in the movement of output conveyor

Reserved Code

Reserved Function of driver. Please make inquiries when error is detected.

42131e Error in the movement of output conveyor

Reserved Code

Reserved Function of driver. Please make inquiries when error is detected.

42131f Error in the movement of output conveyor

System Error on positioning conveyor

System Error of internal driver. Driver error is supposed if this problem happens

frequently.

421401 Error in the movement of upper conveyor

Error in the upper conveyor

Please transit again after returning P.C.B. position.

421501 Error in the movement of lower conveyor

Error in the lower conveyor

Please transit again after returning P.C.B. position.

421601 A-lane output conveyor

-----

421701 B-lane Input conveyor

-----

421801 B-lane positioning conveyor

-----

3.3 Conveyor

4OM-1840

3-3-311604-001

Error ID Error Name, Description, Cause, and Remedy

421901 B-lane output conveyor

-----

422001 Simultaneous transfer timeout

Timeout during simultaneous transfer

Time-out of placement on Output Conveyor, Positioning Conveyor.

Please check P.C.B. position on conveyor.

422101 Input conveyor error

P.C.B. placement was not completed within predetermined time.

Time-out of P.C.B. placement from Input.

There is possibilities that P.C.B. is stopping on conveyor and it is not detected in

sensor. Please check Stagnated P.C.B..

422102 Input conveyor error

P.C.B. on input section was detected before placement is ready completely

The supplying entrance sensor detected P.C.B.(Carried out manual bypass, or

Placed between 2 pieces of Stagnated P.C.B. on conveyor)

422103 Input conveyor error

Placement is completed, but P.C.B. is not placed.

It stopped in the position where could not detect P.C.B. by P.C.B. slit, or P.C.B.

is fallen. Please check P.C.B. of supplying section, and reset it. Conrm the

adjustment of the width of Conveyor.(Set P.C.B. the position detected by sensor)

422104 Input conveyor error

Stop sensor of Input conveyor was detected while P.C.B. was ready for placing.

Remove Stagnated P.C.B., Please set P.C.B. correct positioning. (manual moving)

422201 positioning conveyor Error

Time Over in placement of product position(L)

Motor is not completed. Please check motor error or Pattern program set value

because there is a possibility that time-over value is inputted.

422202 positioning conveyor Error

Time Over in the downward on Backup(L) axis

-----

422203 positioning conveyor Error

Conveyor did not stop

-----

422204 positioning conveyor Error

Upward timeout on Backup(L) axis

Motor is not completed. Please check motor error or Pattern program set value

because there is a possibility that time-over value is inputted.

422301 positioning conveyor Error

Time Over in placement of product position(R)

Remove Stagnated P.C.B., Please set P.C.B. correct positioning. (manual moving)

422302 positioning conveyor Error

Time Over in the downward on Backup(R) axis

Motor is not completed. Please check motor error or Pattern program set value

because there is a possibility that time-over value is inputted.

3.3 Conveyor

4OM-1840

3-3-321604-001