4M184002w_F8S.pdf - 第238页
Error ID Error Name, Description, Cause, and Remedy 49661f Error of Shuttle Conveyor width W2 in Output side System Error in Conveyor Width W2. System Error of internal driver . Driver error is supposed if this problem h…
Error ID Error Name, Description, Cause, and Remedy
496612 Error of Shuttle Conveyor width W2 in Output side
Out-of-Control in Conveyor Width W2
Motor Out-of-Control which is over the width of Out-of-Control detecting occurred.
Please execute all zeroing again, and the restart production.
Please set motor speed slow if it happens frequently. Also, in a case of structure
motor Error.
496613 Error of Shuttle Conveyor width W2 in Output side
Error in Motor Power voltage of Conveyor Width W2
Motor power voltage dropped. Check out the Power supply line(48V Line)
496614 Error of Shuttle Conveyor width W2 in Output side
STP input in Conveyor Width W2 was detected
STP input is detected. The function to stop motor by Hard signal.
496615 Error of Shuttle Conveyor width W2 in Output side
Over-current in Conveyor Width W2
Error in Motor output line. Check out the motor wiring,
496616 Error of Shuttle Conveyor width W2 in Output side
Limit Sensor(+) was detected in Conveyor Width W2.
+LS signal was detected for moving for (+).
Please check the dirt of +LS sensor, disconnection.
496617 Error of Shuttle Conveyor width W2 in Output side
Limit Sensor(-) was detected in Conveyor Width W2.
-LS signal was detected for moving for (-).
Please check the dirt of -LS sensor, disconnection.
496618 Error of Shuttle Conveyor width W2 in Output side
Motor Disconnection of Conveyor Width W2 was detected.
Disconnection to motor was detected.(Only stop mode)
Check the motor wiring.
496619 Error of Shuttle Conveyor width W2 in Output side
Control Power Voltage of Conveyor Width W2 has an error
Control power for driver dropped. Check out the Power supply line.(24V Line)
49661a Error of Shuttle Conveyor width W2 in Output side
-----
Reserved Function of driver. Please make inquiries when error is detected.
49661b Error of Shuttle Conveyor width W2 in Output side
-----
Reserved Function of driver. Please make inquiries when error is detected.
49661c Error of Shuttle Conveyor width W2 in Output side
-----
Reserved Function of driver. Please make inquiries when error is detected.
49661d Error of Shuttle Conveyor width W2 in Output side
-----
Reserved Function of driver. Please make inquiries when error is detected.
49661e Error of Shuttle Conveyor width W2 in Output side
-----
Reserved Function of driver. Please make inquiries when error is detected.
3.6 Automatic Adjustment
4OM-1840
3-3-761604-001
Error ID Error Name, Description, Cause, and Remedy
49661f Error of Shuttle Conveyor width W2 in Output side
System Error in Conveyor Width W2.
System Error of internal driver. Driver error is supposed if this problem happens
frequently.
496701 Conveyor Width W3 Error
Drive Alarm during Conveyor Width W3 axial operation.
Conrm reset Method of detailed Sub-system error counts of Alarm.
496702 Conveyor Width W3 Error
Conveyor Width W3-axis could not start
A state in which the operating command is not normally accepted.
1. Conrm connection to communication cable.
2. Conrm Power supply(24V).
3. Conrm the communication setting of PCI board.
4. Conrm the address of driver and communication rate setting.
496710 Conveyor Width W3 Error
System setup of Conveyor Width W3 is not completed.
Driver has not completed the parameter setup yet. It is a situation in which
a correct setup has not been received by Communication Error. Check the
Communication Mode, wiring, Power supply of Driver.
496711 Conveyor Width W3 Error
Zeroing Error in Conveyor Width W3
LS, discontinuous zeroing movement, was detected. Check out the dirt, error of
sensor and error in Motor body etc.
496212 Conveyor Width W3 Error
Out-of-Control in Conveyor Width W3
Motor Out-of-Control which is over the width of Out-of-Control detecting occurred.
Please execute all zeroing again, and the restart production. Please set motor
speed slow if it happens frequently. Also, in a case of structure motor Error.
496713 Conveyor Width W3 Error
Error in Motor Power voltage of Conveyor Width W3
Motor power voltage dropped. Check out the Power supply line(48V Line)
496714 Conveyor Width W3 Error
STP input in Conveyor Width W3 was detected
STP input is detected. The function to stop motor by Hard signal.
496715 Conveyor Width W3 Error
Over-current in Conveyor Width W3
Error in Motor output line. Check out the motor wiring,
496716 Conveyor Width W3 Error
Limit Sensor(+) was detected in Conveyor Width W3.
+LS signal was detected for moving for (+).
Please check the dirt of +LS sensor, disconnection.
496717 Conveyor Width W3 Error
Limit Sensor(-) was detected in Conveyor Width W3.
-LS signal was detected for moving for (-).
Please check the dirt of -LS sensor, disconnection.
3.6 Automatic Adjustment
4OM-1840
3-3-771604-001
Error ID Error Name, Description, Cause, and Remedy
496718 Conveyor Width W3 Error
Motor Disconnection of Conveyor Width W3 was detected.
Disconnection to motor was detected.(Only stop mode)
Check the motor wiring.
496719 Conveyor Width W3 Error
Control Power Voltage of Conveyor Width W3 has an error
Control power for driver dropped. Check out the Power supply line.(24V Line)
49671a Conveyor Width W3 Error
-----
Reserved Function of driver. Please make inquiries when error is detected.
49671b Conveyor Width W3 Error
-----
Reserved Function of driver. Please make inquiries when error is detected.
49671c Conveyor Width W3 Error
-----
Reserved Function of driver. Please make inquiries when error is detected.
49671d Conveyor Width W3 Error
-----
Reserved Function of driver. Please make inquiries when error is detected.
49671e Conveyor Width W3 Error
-----
Reserved Function of driver. Please make inquiries when error is detected.
49671f Conveyor Width W3 Error
System Error in Conveyor Width W3.
System Error of internal driver. Driver error is supposed if this problem happens
frequently.
496720 Conveyor Width W3 Error
Communication Error in Conveyor Width W3.
1. Conrm connection to communication cable.
2. Conrm Power supply(24V).
3. Conrm the communication setting of PCI board.
4. Conrm the address of driver and communication rate setting.
496801 Transit communication Error
Communication error occurred in the transfer section.
1. Conrm connection to communication cable.
2. Conrm Power supply(24V).
3. Conrm the communication setting of PCI board.
4. Conrm the address of driver and communication rate setting.
496802 Conveyor Width W1-axis communication Error
Communication error occurred in the W1-axis transfer driver.
1. Conrm connection to communication cable.
2. Conrm Power supply(24V).
3. Conrm the communication setting of PCI board.
4. Conrm the address of driver and communication rate setting.
3.6 Automatic Adjustment
4OM-1840
3-3-781604-001