4M184002w_F8S.pdf - 第229页

Error ID Error Name, Description, Cause, and Remedy 496001 Conveyor Width Backup Pin detected Backup Pin/Jig was detected during N1_W1-axis operating. Please remove the Backup Pin\Jig from Backup Base. Or , conrm whethe…

Error ID Error Name, Description, Cause, and Remedy

490795 Nozzle set up

Error in the nozzle stocker mark recog. There is a possibility that the stocker type

is wrong.

Please conrm that the set stocker in the unit replace screen is the same as the

stocker type of the device. Please clean it up if there is no problem.

490796 Nozzle set up

It is impossible to place a nozzle whose end type is set besides [standard]

adjacent to a head.

-----

490797 Nozzle set up

It stopped by nozzle interference check.

Perform zeroing.

490798 Nozzle set up

Error in communication with recognition.

-----

490799 Nozzle set up

Time-out of communication with recognition.

-----

49079a Nozzle set up

Error in capturing a image with component recognizing camera.

-----

49079b Nozzle set up

To capture a image with component recognizing camera is not complete with the

predetermined time.

-----

49079c Nozzle set up

Error in recognition of nozzle position.

-----

49079d Nozzle set up

Time-out of recognition of nozzle position.

-----

49079e Nozzle set up

Failed in nozzle position teaching. Please conrm Nozzle ID, and then replace a

nozzle.

-----

49079f Nozzle set up

To set nozzle position data failed.

-----

4907A0 Nozzle set up

The nozzle stocker which is not for replace exists on input position.

Please perform all zeroing.

490801 Program -change linked operation

Program-change linked operation has not nished within appointed time.

-----

3.6 Automatic Adjustment

4OM-1840

3-3-671604-001

Error ID Error Name, Description, Cause, and Remedy

496001 Conveyor Width Backup Pin detected

Backup Pin/Jig was detected during N1_W1-axis operating.

Please remove the Backup Pin\Jig from Backup Base. Or, conrm whether

Sensor has error or not.

496002 Conveyor Width Backup Pin detected

Backup Pin/Jig was detected during N1_W2-axis operating.

Please remove the Backup Pin\Jig from Backup Base. Or, conrm whether

Sensor has error or not.

496003 Conveyor Width Backup Pin detected

Backup Pin/Jig was detected during N1_W3-axis operating

Please remove the Backup Pin\Jig from Backup Base. Or, conrm whether

Sensor has error or not.

496101 Conveyor Width W1 Error

Drive Alarm during Conveyor Width W1 axial operation.

Conrm reset Method of detailed Sub-system error counts of Alarm.

496102 Conveyor Width W1 Error

Conveyor Width W1-axis could not start

A state in which the operating command is not normally accepted.

1. Conrm connection to communication cable.

2. Conrm Power supply(24V).

3. Conrm the communication setting of PCI board.

4. Conrm the address of driver and communication rate setting.

496110 Conveyor Width W1 Error

System setup of Conveyor Width W1 is not completed.

Driver has not completed the parameter setup yet. It is a situation in which a

correct setup has not been received by Communication Error.

Check the Communication Mode, wiring, Power supply of Driver.

496111 Conveyor Width W1 Error

Zeroing Error in Conveyor Width W1

LS, discontinuous zeroing movement, was detected.

Check out the dirt, error of sensor and error in Motor body etc.

496112 Conveyor Width W1 Error

Out-of-Control in Conveyor Width W1

Motor Out-of-Control which is over the width of Out-of-Control detecting occurred.

Please execute all zeroing again, and the restart production.

Please set motor speed slow if it happens frequently. Also, in a case of structure

motor Error.

496113 Conveyor Width W1 Error

Error in Motor Power voltage of Conveyor Width W1

Motor power voltage dropped. Check out the Power supply line(48V Line)

496114 Conveyor Width W1 Error

STP input in Conveyor Width W1 was detected

STP input is detected. The function to stop motor by Hard signal.

3.6 Automatic Adjustment

4OM-1840

3-3-681604-001

Error ID Error Name, Description, Cause, and Remedy

496115 Conveyor Width W1 Error

Over-current in Conveyor Width W1

Error in Motor output line. Check out the motor wiring,

496116 Conveyor Width W1 Error

Limit Sensor(+) was detected in Conveyor Width W1.

+LS signal was detected for moving for (+).

Please check the dirt of +LS sensor, disconnection.

496117 Conveyor Width W1 Error

Limit Sensor(-) was detected in Conveyor Width W1.

-LS signal was detected for moving for (-).

Please check the dirt of -LS sensor, disconnection.

496118 Conveyor Width W1 Error

Motor Disconnection of Conveyor Width W1 was detected.

Disconnection to motor was detected.(Only stop mode)

Check the motor wiring.

496119 Conveyor Width W1 Error

Control Power Voltage of Conveyor Width W1 has error

Control power for driver dropped. Check out the Power supply line.(24V Line)

49611a Conveyor Width W1 Error

-----