4M184002w_F8S.pdf - 第65页
4OM-1840 1-1-8 1604-001 1.3 Items for Periodic Maintenance The items (inspection, cleaning, lubrication, etc.) that require periodic Reference Ref…
4OM-1840
1-1-71604-001
(4) Syringe
Maker: TERUMO
This gun can be used for two types of greases.
Use the syringes and the nozzle properly.
Two Types of Greases : DAPHNE GREASE MP No. 1
MOLYNOC GREASE AP1
Appearance
Fig. 4A1-5
Table 4A1-4
Standard Shape Part No. Remarks
Syringe
KYB-M382K-00
228A0171
Maker : TERUMO
10ml SS-10-LZ
Nozzle No.18
(Color : Green)
---
216G0451
Maker : SAN-EI TECH
Inside Diameter :
f
0.84
Tapered Nozzle #5118TT-B
Nozzle No.19
(Color : Brown)
KYB-M380X-00
0916D108
Maker : NIPRO
Inside Diameter :
f
0.79
Length : 65 mm Flat End
1.2 Preparation for Maintenance
4OM-1840
1-1-81604-001
1.3 Items for Periodic Maintenance
The items (inspection, cleaning, lubrication, etc.) that require periodic
Reference
Refer to "2. Maintenance Check List" in "Chapter 1" for the maintenance based
on frequency of use.
Notice
The * -marks represent that the items require maintenance only for the
rst time.
Follow the ○-marked maintenance cycle for the subsequent use.
Table 4A1-5
Device Name
Inspection Cleaning,
and Lubricating Spots
Work
Maintenance Cycle
Daily Weekly
Monthly
Every
3 Months
Every
6 Months
Yearly
Every
2 years
4.1 Air Source
Main Air Pressure
Inspection
Air Blowing Pressure
Inspection
Z Clamp Pressure
Inspection
Drain
Cleaning
Filter
Cleaning
4.2 Vacuum System
Vacuum Pressure
Inspection
Filter
Cleaning
4.3 Component
Recognition
Camera Section
Component Recognition
Camera
Cleaning
Component Storage Box
Cleaning
Fiducial Mark
Cleaning
4.4 Feeder Base
Driving Section
Worm Gear
Lubrication
4.5 Feeder Cart
Section
Groove on Feeder Base
Cleaning
Upper Surface of Feeder
Base
Cleaning
Real Box
Cleaning
Scrap Box
Cleaning
1.3 Items for Periodic Maintenance
4OM-1840
1-1-91604-001
Table 4A1-6
Device Name
Inspection Cleaning,
and Lubricating Spots
Work
Maintenance Cycle
Daily Weekly
Monthly
Every
3 Months
Every
6 Months
Yearly
Every
2 years
4.6
Cutter Section
Cutter Unit
Cleaning
Lubrication
Movable Blade
Change
Change
Change
4.7 Head Section
Nozzle U/D Ball Screw
(NL Axis)
Cleaning,
Lubrication
Cleaning
Linear Measure Sensor
(Light Emitter and
Receiver)
Cleaning
Nozzle Change Cam Face
(Lower Side)
Cleaning,
Lubrication
Center Spline
Lubrication
Cam Follower
Cleaning,
Lubrication
Vacuum Filter
Change
Nozzle Filter
Change
Head U/D Ball Screw
(HL Axis)
Cleaning,
Lubrication
Head U/D Linear Guide
(HL Axis)
Cleaning,
Lubrication
*
Note
The head up/down ball screw (HL-axis) and the head up/down linear guide
(HL-axis) are applicable only to the SIGMA-F8S high-speed multi-purpose
head.
1.3 Items for Periodic Maintenance