4M184002w_F8S.pdf - 第66页

4OM-1840 1-1-9 1604-001 T able 4A1-6 Device Name Inspection Cleaning, and Lubricating Spots Work Maintenance Cycle Daily Weekly Monthly Every 3 Months Every 6 Months Y early Every 2 years 4.6 Cutter Section Cutter Unit C…

100%1 / 315
4OM-1840
1-1-81604-001
1.3 Items for Periodic Maintenance
The items (inspection, cleaning, lubrication, etc.) that require periodic

Reference
Refer to "2. Maintenance Check List" in "Chapter 1" for the maintenance based
on frequency of use.
Notice
The * -marks represent that the items require maintenance only for the
rst time.
Follow the ○-marked maintenance cycle for the subsequent use.
Table 4A1-5
Device Name
Inspection Cleaning,
and Lubricating Spots
Work
Maintenance Cycle
Daily Weekly
Monthly
Every
3 Months
Every
6 Months
Yearly
Every
2 years
4.1 Air Source
Main Air Pressure
Inspection
Air Blowing Pressure
Inspection
Z Clamp Pressure
Inspection
Drain
Cleaning
Filter
Cleaning
4.2 Vacuum System
Vacuum Pressure
Inspection
Filter
Cleaning
4.3 Component
Recognition
Camera Section
Component Recognition
Camera
Cleaning
Component Storage Box
Cleaning
Fiducial Mark
Cleaning
4.4 Feeder Base
Driving Section
Worm Gear
Lubrication
4.5 Feeder Cart
Section
Groove on Feeder Base
Cleaning
Upper Surface of Feeder
Base
Cleaning
Real Box
Cleaning
Scrap Box
Cleaning
1.3 Items for Periodic Maintenance
4OM-1840
1-1-91604-001
Table 4A1-6
Device Name
Inspection Cleaning,
and Lubricating Spots
Work
Maintenance Cycle
Daily Weekly
Monthly
Every
3 Months
Every
6 Months
Yearly
Every
2 years
4.6
Cutter Section
Cutter Unit
Cleaning

Lubrication
Movable Blade
Change

Change

Change
4.7 Head Section
Nozzle U/D Ball Screw
(NL Axis)
Cleaning,
Lubrication

Cleaning
Linear Measure Sensor
(Light Emitter and
Receiver)
Cleaning
Nozzle Change Cam Face
(Lower Side)
Cleaning,
Lubrication
Center Spline
Lubrication
Cam Follower
Cleaning,
Lubrication
Vacuum Filter
Change
Nozzle Filter
Change
Head U/D Ball Screw
(HL Axis)
Cleaning,
Lubrication
Head U/D Linear Guide
(HL Axis)
Cleaning,
Lubrication
*
Note
The head up/down ball screw (HL-axis) and the head up/down linear guide
(HL-axis) are applicable only to the SIGMA-F8S high-speed multi-purpose
head.
1.3 Items for Periodic Maintenance
4OM-1840
1-1-101604-001
Table 4A1-7
Device Name
Inspection Cleaning,
and Lubricating Spots
Work
Maintenance Cycle
Daily Weekly
Monthly
Every
3 Months
Every
6 Months
Yearly
Every
2 years
4.8 X/Y Beam Section

Inspection

Cleaning,
Lubrication
*
Y-Axis Linear Guide
Inspection
Y-Axis Linear Guide
Cleaning,
Lubrication
*

Cleaning,
Lubrication

Places
Inspection

Cleaning
Y-Axis Cable Side Face
Cleaning,
Lubrication
Y-Axis Cable Fixing
Places
Inspection
Y-Axis Linear Scale
Cleaning
4.9 PCB Positioning
Section
Upper Surface of Backup
Table
Cleaning
Ball Screw
Cleaning,
Lubrication
*
Ball Screw Spline
Cleaning,
Lubrication
4.10
Conveyor Section
Linear Guide
Cleaning,
Lubrication
*
Support Pin Detection
Sensors
Cleaning,
Lubrication
PCB Detection Sensor
Cleaning
4.11 Nozzle Stocker
Section
Nozzle Storage Section
Cleaning
Nozzle Stocker Sliding
Area
Cleaning,
Lubrication
Shutter Flange Pin Sliding
Section
Cleaning,
Lubrication
4.12 Control Box
Section
Filter
Cleaning
Note
The item "Ball Screw Spline (4.9 PCB Positioning Unit)" is for the system
where the Y510mm Single Transfer Unit (Factory option) has been mounted.
1.3 Items for Periodic Maintenance