00191025-01.pdf - 第596页

SIPLACE 80S/F/G User’s Manual 19 Error Message s Edition 12/96 from S oftware Version SR.009.xx 19.1 Error Messages 19 - 9 79 Arm for tur ning station 1 has not swivelled out CAUSE ● Feed m otor defec tive; prox imity s …

100%1 / 736
19 Error Messages SIPLACE 80S/F/G User’s Manual
19.1 Error Messages Edition 12/96 from Software Version SR.009.xx
19 - 8
63 X axis disabled
CAUSE
●
x axis switched off at the axis controller switch.
REMEDY
●
x axis should be switched on at the axis controller switch.
64 Y axis disabled
CAUSE
●
y axis switched off at the axis controller switch.
REMEDY
●
y axis should be switched on at the axis controller switch.
65 D1 axis disabled
CAUSE
●
dp1 axis switched off at the axis controller switch.
REMEDY
●
dp1 axis should be switched on at the axis controller switch.
66 D2 axis disabled
CAUSE
●
dp2 axis switched off at the axis controller switch.
REMEDY
●
dp2 axis should be switched on at the axis controller switch.
67 Star axis disabled
CAUSE
●
Star axis switched off at the axis controller switch.
REMEDY
●
Star axis should be switched on at the axis controller switch.
68 Z axis disabled
CAUSE
●
z axis switched off at the axis controller switch.
REMEDY
●
z axis should be switched on at the axis controller switch.
75 Programmed position of Z axis outside travel range
CAUSE
●
Machine data in the line computer erroneous; height reference run is not carried out on the PCB
conveyor.
REMEDY
●
Check the machine data in the line computer.
SIPLACE 80S/F/G User’s Manual 19 Error Messages
Edition 12/96 from Software Version SR.009.xx 19.1 Error Messages
19 - 9
79 Arm for turning station 1 has not swivelled out
CAUSE
●
Feed motor defective; proximity switch defective.
REMEDY
●
Replace feed motor; carry out axis calibration; fit new proximity switch.
80 Arm for turning station 2 has not swivelled out
CAUSE
●
Feed motor defective; proximity switch defective.
REMEDY
●
Replace feed motor; carry out axis calibration; fit new proximity switch.
94 DETERMINANT not correct during position recognition
CAUSE
●
The two fiducials of a circuit image are on one position; the three fiducials of a circuit image are in a
line.
REMEDY
●
Correct placement program in the line computer.
95 Fiducial missing in position recognition
CAUSE
●
Fiducial quality of a fiducial not adequate; PCB transport adjusted imprecisely; camera illumination
defective; search field too small.
REMEDY
●
Clean fiducial; reteach fiducial (increase size of search field); check conveyor width; check stopper
setting.
96 CORR_MOVE not correct during position recognition
CAUSE
●
The two fiducials of a circuit image are on one position.
REMEDY
●
Correct placement program in the line computer.
101 Track empty, no component during pick-up
CAUSE
●
On a single track at least three pick-up errors occurred immediately after one another; no compo-
nent in the pick-up position; set up for incorrect component (e.g. cubic instead of non-cubic).
feeder jamming; cover foil parted.
REMEDY
●
Refill components and reset track; check set-up.
get feeder working properly again.
19 Error Messages SIPLACE 80S/F/G User’s Manual
19.1 Error Messages Edition 12/96 from Software Version SR.009.xx
19 - 10
102 Quality too low during optical centering
CAUSE
●
Parameters for optical centering erroneous.
REMEDY
●
Check the package form in the components manipulator.
103 Spacing of a pin group out of tolerance
CAUSE
●
Bent terminal pin; pitch error limit defined too small.
REMEDY
●
Check components; increase pitch error limit in the package form editor.
104 Component angle outside of tolerance
CAUSE
●
Angular positioning deviation of the component on the nozzle too great; angular positioning toler-
ance defined too small.
REMEDY
●
Improve pick-up; increase angular positioning tolerance.
121 Peak offset: no result
CAUSE
●
Component terminal pin bent.
REMEDY
●
Check quality of the components.
122 Coplanarity module cannot be initialized
CAUSE
●
Coplanarity module not plugged in; configuration jumper incorrectly set
REMEDY
●
Plug in module; correct jumper.
123 Coplan.: Data value outside of range
CAUSE
●
Error in cluster or set-up: PF file faulty
REMEDY
●
Check data for coplanarity in cluster and set-up; check PF data.
124 Vacuum reduction at placem. stat. too slow
CAUSE
●
During placement of a component the vacuum does not reduce fast enough;
forced air not present; forced air defective.
REMEDY
●
Check forced air; check forced air valve.