00198439-03_SIPLACE_JTF-ML2_TX12_V1-V2_DE_EN_CHS.pdf - 第115页
2 Operational safety 2.6 IMDA Registration User Manual / Bedienungsanleitung / 用户手册 SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019 115 2.5.3 FCC Label on SIPLACE JTF‑ML2 Fig.17: FCC label on SIPLACE JTF‑ML2…
2 Operational safety
2.5 FCC, RFID
114 User Manual / Bedienungsanleitung / 用户手册 SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019
2.4.5 Dispatching ESD modules
► Always store modules and components in conductive packaging (e.g. metallized plastic bags
or metal sleeves) and dispatch them in conductive packaging
► If the packaging is not conductive, place the modules in a conductive envelope before pack-
aging. Use conductive expanded rubber, ESD bags, domestic aluminum foil or paper, for
example. NEVER use plastic bags or film.
► If the module has integral batteries, ensure that the conductive packaging does not touch or
short circuit the battery terminals and, if necessary, first cover the terminals with insulating
tape or material.
2.5 FCC, RFID
2.5.1 FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment. This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
► Reorient or relocate the receiving antenna.
► Increase the separation between the equipment and receiver.
► Connect the equipment into an outlet on a circuit different from that to which the recei-
ver is connected.
► Consult the dealer or an experienced radio/TV technician for help.
2.5.2 RFID on SIPLACE JTF-ML2
Fig.16: RFID on SIPLACE JTF-ML2
1. The RFID reader module is located in
the tower of the SIPLACE JTF‑ML2.
2. One RFID tag is located on each
SIPLACE JTF‑ML2 cassette.
2 Operational safety
2.6 IMDA Registration
User Manual / Bedienungsanleitung / 用户手册 SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019 115
2.5.3 FCC Label on SIPLACE JTF‑ML2
Fig.17: FCC label on SIPLACE JTF‑ML2
1. The FCC label is located above the
typeplate.
2.6 IMDA Registration
NOTICE
The equipment listed below has been registered with the Infocommunications Media Devel-
opment Authority under regulation 20(6) of the Telecommunications (Dealers) Regulations
(Cap 323, Rg 6) (the "Dealers Regulations") and approved for sale in Singapore. Your at-
tention is drawn to the relevant provisions and requirements of the Dealers described
below.
Declared Equipment Information
Brand/Trade Name: ASM
Model Name/No.: SIPLACE JTF-ML2
(c/w RFID Module 03146441‑01)
Equipment Description JEDEC Tray Feeder
2.6.1 IMDA Label on SIPLACE JTF‑ML2
The SIPLACE JTF‑ML2 complies with IMDA standards.
Fig.18: IMDA compliance label
2 Operational safety
2.6 IMDA Registration
116 User Manual / Bedienungsanleitung / 用户手册 SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019