00198439-03_SIPLACE_JTF-ML2_TX12_V1-V2_DE_EN_CHS.pdf - 第121页
4 Setting up and commissioning 4.1 Requirements and restrictions User Manual / Bedienungsanleitung / 用户手册 SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019 121 4 Setting up and commissioning NOTICE Example show…
3 Technical data of the module
3.2 Overview – SIPLACE JTF-ML2
120 User Manual / Bedienungsanleitung / 用户手册 SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019
Fig.22: Cassette for 7 trays (optional)
SIPLACE JTF-ML2 Tray Cassette 7
[00588177-xx]
Cassettes for 7 trays can be ordered separ-
ately.
This cassette type can house thin (7.62mm)
and thick (12.19mm) JEDEC trays.
1. Transportation locks (2x)
2. Security spring
3. Handles
4. Guides for JEDEC trays
DANGER
Risk of crashing when using thick JEDEC trays
►
Do not use thick JEDEC trays in combination with C&P20P2 or CPP_L.
Otherwise, the head will be damaged.
4 Setting up and commissioning
4.1 Requirements and restrictions
User Manual / Bedienungsanleitung / 用户手册 SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019 121
4 Setting up and commissioning
NOTICE
Example shown as diagram
The following diagrams are just examples. The procedure is the same for other machine
types than the SIPLACE TX1 / TX2-V1 / V2 shown. Any relevant differences will be men-
tioned explicitly.
4.1 Requirements and restrictions
The following requirements and restrictions apply to the SIPLACE JTF-ML2:
●
Assembly is only possible on SIPLACE TX1 and TX2 machines.
Assembly is not possible on SIPLACE TX2i machines.
●
The software version of a SIPLACE TX1/TX2 V1 machine must be 710.1 or higher. The soft-
ware version of a SIPLACE TX1/TX2 V2 machine must be 711.1 or higher.
●
The assembly is only possible at location 1.
●
The conveyor and the tower of the SIPLACE JTF-ML2 have the same ID number and must al-
ways be working as a pair.
It is not allowed to use a conveyor and a tower with different ID numbers.
Placement Heads
The following placement heads are possible:
●
CPP_H
●
TwinHead
From SIPLACE TX V2:
●
C&P20 P2
●
CPP_L
●
CPP M
Information on additional placement head variants are available upon request.
Also observe: 2.1.5 "Risk of crashing when using thick JEDEC trays" [}108]
Trays
NOTICE
Magnets with reduced height for Cookie Trays
When using magazine sheets (Cookie Trays), magnets with reduced height are required
[03160331‑xx]. For details, refer to the Technical Information "Magnet for JTF-ML2 Cookie
Tray" [DE:TI2019‑06D01] [EN:TI2019‑06E01].
4 Setting up and commissioning
4.2 Retrofitting in the SIPLACE TX-Series
122 User Manual / Bedienungsanleitung / 用户手册 SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019
4.2 Retrofitting in the SIPLACE TX-Series
4.2.1 Scope of delivery for retrofitting in the SIPLACE TX-Series V1
The following parts are required for retrofitting in the SIPLACE TX-Series V1:
●
SIPLACE JTF-ML2 (tray feeder module) [00588116‑xx]
●
Changeover table for SIPLACE JTF-ML [00588112‑xx]
●
Assembly kit for SIPLACE JTF-ML2 [00588117S‑xx]
Additionally required parts on a SIPLACE TX V1:
●
Magazine sheet for SIPLACE JTF-M magazines [03110222Sxx]
●
If you fit the SIPLACE JTF ML2 to a SIPLACE TX V1 with a CPP head, the "Reject box /
nozzle station IC-camera V1"[03162806-xx] and the "Nozzle station CPx cpl. / X4iS,
XS" [03090348-xx] must be ordered in addition!
Assembly kit for SIPLACE JTF-ML2 (SIPLACE TX V1)
Count Designation Item no.
1 SIPLACE JTF-ML2 adapter for SIPLACE TX machine complete 03129004‑xx
1 Empty tape duct, short TX assembly 03121376-xx
1 Mounting support TX-JTF assembly 03136824-xx
1 Cable COTi TX: DC control to SIPLACE JTF-ML 03134469-xx
1 Cable COTi TX: CAN bus3 to SIPLACE JTF-ML 03134468-xx
1 Cover assembly for SIPLACE JTF complete 03119382-xx
1 Dummy feeder 12 tracks 03154408- xx
1 Cable: Power Adapter JTF 03160347- xx
4.2.1.1 Overview of Parts
Fig.23: SIPLACE JTF-ML2 tower
Fig.24: SIPLACE JTF-ML2 conveyor
Fig.25: SIPLACE JTF-ML2 adapter
Fig.26: Dummy feeder 12 tracks