00198382-03_UM_SIPLACE-CA4-V2_EN.pdf - 第148页
4 Setting up and commissioning Instruction manual SIPLACE CA4 V2 4.1 Delivery configuration and tr ansportation of placement mach ines From softwa re version 713.0 Edition 12/2019 148 4.1.5.2 Means of conveyor Use a fork…
Instruction manual SIPLACE CA4 V2 4 Setting up and commissioning
From software version 713.0 Edition 12/2019 4.1 Delivery configuration and transportation of placement machines
147
4.1.4.4 Fork-lift attachment points on the conveyor crate or pallet
Position the fork-lift truck only at the points marked (A). in fig. 4.1 - 1, page 143. We recommend
that you keep the crate or the pallet with packaging for later use.
4
4.1.5 Transporting the placement machine without a crate or pallet
4.1.5.1 Safety instructions
4
4
4
4
WARNING
Damage to property on the placement machine!
There is a risk of damaging the placement machine if it is transported without crate or
pallet.
Observe the information in the next section.
WARNING
Observe the applicable accident prevention regulations!
The applicable accident prevention regulations concerning the transportation of
heavy goods must be followed.
WARNING
DANGER OF CRUSHING!
Risk of crushing feet when transporting the placement machine.
Wear special protective shoes.
WARNING
Damage to property on the placement machine!
There is a risk of damaging the placement machine if it is transported without crate or
pallet.
Read this section through completely before transporting the machine.
WARNING
Risk of damage!
The thread for the machine feet in the machine frame could be damaged by being
dragged along the floor or from impact.
When you are transporting the machine, make sure that all the feet are clear of the
floor.
4 Setting up and commissioning Instruction manual SIPLACE CA4 V2
4.1 Delivery configuration and transportation of placement machines From software version 713.0 Edition 12/2019
148
4.1.5.2 Means of conveyor
Use a fork-lift truck with the following specification to carry the placement machine:
4.1.5.3 Fork-lift attachment points on the placement machine
The diagram 4.1 - 3, page 149 shows the fork-lift attachment points on the placement machine for
lifting the placement machine off the pallet or transporting it without the pallet.
4
4
Please note the following points before you raise the placement machine in order to avoid irre-
versible damage to the placement machine:
4
4
Fork length Min. 1800 mm
Lifting power Min. 6,000 kg
Distance between forks with the forks running parallel
to the direction of PCB conveyor
Approx. 420 mm
PLEASE NOTE
Avoiding damage to the placement machine
When transporting the placement machine over longer distances, always use a pal-
let and fork lift.
WARNING
Aligning the forks
– The forks must be aligned parallel to the PCB conveyor.
– The forks must be aligned parallel to the placement machine.
WARNING
Risk of damage due to excessive fork spacing!
Increased fork spacing, which means that the placement machine is raised at points out-
side its contact surface, can lead to deformation of the placement machine frame and
cause damage to cables and lines.
The forks may only be opened to a degree which ensures that they are still within the
contact area of the machine underside (see fig. 4.1 - 3
, page 149).
Instruction manual SIPLACE CA4 V2 4 Setting up and commissioning
From software version 713.0 Edition 12/2019 4.1 Delivery configuration and transportation of placement machines
149
4
4
Fig. 4.1 - 3 Contact surfaces - forks parallel to the direction of PCB conveyor
(1) Contact surface for fork lift truck forks
4
4
WARNING
Risk of damage due to one-sided loading!
One-sided loading of the machine feet e.g. from tilting the machine, can lead to deforma-
tion of the machine feet fixtures.
Make sure that the forks are evenly loaded when you lift the placement machine.
Use a firm support layer between the forks and the placement machine.
Enlist the help of a second person to watch while you lift the placement machine and
make sure that the placement machine does not tip over to one side.
(1)