00198382-03_UM_SIPLACE-CA4-V2_EN.pdf - 第230页
5 Tasks at the placement machine Instruction manual SIPLACE CA4 V2 5.10 Setting up the feeder modules From software version 713.0 E d ition 12/2019 230 5.10.3.2 Inserting the X feeder module into the ch angeover table 5 …
Instruction manual SIPLACE CA4 V2 5 Tasks at the placement machine
From software version 713.0 Edition 12/2019 5.10 Setting up the feeder modules
229
If the removal handle (item 1) is still protruding, then latch it in place.
5
Fig. 5.10 - 2 Check the X feeder module before using it
(1) Removal handle
(2) Cover foil rocker
(3) Pickup window
(4) Lever for raising and latching the pick-up window
(5) Component disposal compartment
(1)
(2)
(3)
(4)
(5)
5 Tasks at the placement machine Instruction manual SIPLACE CA4 V2
5.10 Setting up the feeder modules From software version 713.0 Edition 12/2019
230
5.10.3.2 Inserting the X feeder module into the changeover table
5
Fig. 5.10 - 3 Inserting the X feeder module into the changeover table
(1) Front slider guide for the X feeder module
(2) Back slider guide for the X feeder module
(3) "Back" centering pin on the X feeder module
(4) "Front" centering pin on the X feeder module
(5) Recesses in the centering bar for holding the "back" centering pin
(6) Centering holes on the changeover table for holding the "front" centering pin
(7) Locking latches
(8) Guide profile for the changeover table ( profile)
(9) Insertion aid for the feeder module
5
Place the front slider guide (item 1 in fig. 5.10 - 3) of the feeder module on the insertion aid
(item 9 in fig. 5.10 - 3
) of the changeover table.
Hold the feeder module vertically and push it forward, along the guide profile (item 8 in fig.
5.10 - 3
). The front (item 1 in fig. 5.10 - 3) and rear (item 2 in fig. 5.10 - 3) slider guides of the
feeder module slide on the guide profile (item 8 in fig. 5.10 - 3
).
Carefully push the feeder module further until the "front" centering pin (item 4 in fig. 5.10 - 3,
page 230
) is pushed into the centering hole (item 6 in fig. 5.10 - 3, page 230).
(8)
(9)
(5)
(3)
(2)
(1)
(4)
Instruction manual SIPLACE CA4 V2 5 Tasks at the placement machine
From software version 713.0 Edition 12/2019 5.10 Setting up the feeder modules
231
Check the "back" centering pin (item 3 in fig. 5.10 - 3, page 230) of the feeder module as you
do so. This must slide easily into the recess (item 5) in the centering bar, otherwise the feeder
module is not seated vertically on the changeover table or it was not placed on the guide pro-
file (item 8 in fig. 5.10 - 3
, page 230) correctly.
When the feeder module is at the stop position, the locking latch (item 7 in fig. 5.10 - 3, page
230
) engages onto the locking roller of the feeder module. If you
have forgotten to engage the removal handle (item 1 in fig. 5.10 - 2
, page 229) the status dis-
play on the feeder module's operator panel will light up red after a few seconds.
Engage the removal handle (item 1 in fig. 5.10 - 2, page 229). The feeder module's status
display now lights up green and the feeder module is on standby.
5.10.4 Placing the component tape on the X feeder module
5.10.4.1 Checking the X tape feeder module
When you place the component tape in the feeder module, first check whether there are
any components in the vicinity of the pickup window (item 2 in fig. 5.10 - 5
, page 233).
Remove any components that you find since they could cause a fault.
5.10.4.2 Preparing the component tape for insertion
Check that there is a straight cut edge at the start of the component tape.
If the conveyor holes are torn or bent, cut off this part of the tape.
Also make sure that there are no streaks of adhesive on the cover foil.
Pull around 30 cm cover foil away from the component tape if this does not expose any com-
ponents.
5
Shorten the component tape with the now exposed component pockets by around 3 cm.
Remove the components from the open tape pockets.
Wrap the cover foil around the front edge of the tape along the bottom of the tape.
PLEASE NOTE
Avoid loss of components
If there is not enough cover foil present, use the SMD tape threader:
for the 8 mm tape: Item no. 00355265-xx 5
for the 12 mm tape: Item no. 00356342-xx 5