00198382-03_UM_SIPLACE-CA4-V2_EN.pdf - 第168页
4 Setting up and commissioning Instruction manual SIPLACE CA4 V2 4.3 Setting up the placement mac hine From software versio n 713.0 Edition 12/2019 168 4.3.6 Presetting board conveyor height Push the forks of the f ork…
Instruction manual SIPLACE CA4 V2 4 Setting up and commissioning
From software version 713.0 Edition 12/2019 4.3 Setting up the placement machine
167
4.3.4 PCB conveyor height on the placement machine
The placement machine can be set to the following PCB conveyor heights:
900 mm ± 15 mm 4
930 mm ± 15 mm (standard height) 4
950 mm ± 15 mm (SMEMA height) 4
4
4.3.5 Tools and equipment
You will need the following tools and equipment to adjust the height of your placement machine:
– Fork wrench SW 36, Item no. 00096286-01
– Wrench of width 36 for the setting screw M24x2x120 used to adjust the height of the machine
feet.
– Hook wrench 135 - 145 for adjusting the middle machine feet,
Item no. 00376519-xx
– Single head wrench SW 65, Item no. 00353827-0, width 65 for the hexagonal lock nut M24
on the middle machine foot
– Allen wrench, size 10, Item no. 00373926-01 for hexagon socket-head screws M12x80 for
fastening the spacers on the middle machine feet
– Allen wrench, size 19, Item no. 00373928-01 for hexagon socket-head screw M24x90 for
temporary fixture of clamping pieces for the four outer machine feet
– Torque wrench with hexagonal pin, size 19, tightening torque 130 Nm
for final fastening of four outer machine feet
– Machine spirit level: accuracy 0.02 mm/m
– Fork lift truck (specification see 4.1.4.3 on page 146).
– Air cushion conveyor system: SIPLACE HSxx, Item No. 00119002-S01 (optional)
PLEASE NOTE
The PCB conveyor height is the distance between the top edge of the PCB conveyor belt
and the bottom edge of the machine feet.
4 Setting up and commissioning Instruction manual SIPLACE CA4 V2
4.3 Setting up the placement machine From software version 713.0 Edition 12/2019
168
4.3.6 Presetting board conveyor height
Push the forks of the fork lift under the placement machine, as shown in fig. 4.3 - 2.
4
Fig. 4.3 - 2 Contact surfaces - forks parallel to the direction of PCB conveyor
(1) Contact surfaces for fork lift truck forks
Please note the following points before you raise the placement machine in order to avoid irre-
versible damage to the placement machine:
4
WARNING
Risk of damage due to excessive fork spacing!
The spacing of the machine feet is 776 mm. Increasing this spacing, so that the place-
ment machine is lifted up via the side sections of its machine frame, can lead to defor-
mation of the machine frame.
The forks may only be opened to a degree which ensures that they are still within
the contact area of both machine feet (see fig. 4.3 - 2
, page 168).
(1)
Instruction manual SIPLACE CA4 V2 4 Setting up and commissioning
From software version 713.0 Edition 12/2019 4.3 Setting up the placement machine
169
4
With the fork-lift, raise the placement machine approximately 35 cm. This prevents the risk of
any injuries to your feet if the machine feet are unintentionally lowered.
The placement machine stands on 6 feet.
– 4 outer machine feet (item 1 in fig. 4.3 - 4
, page 170 )
– Outer machine feet for the PCB conveyor heights 900,930 and 950 mm, length
439 mm, Item no. 03000890-02 (item 1 in fig. 4.3 - 3
).
– 2 middle machine feet (item 2 in fig. 4.3 - 4
, page 170) with 2 spacers (item 3 and 4 in fig. 4.3
- 4, page 170) for height adjustment, where necessary.
4
Fig. 4.3 - 3 Outer machine feet - two versions (dimensions in millimeters)
WARNING
Risk of damage due to one-sided loading!
One-sided loading of the machine feet e.g. from tilting the machine, can lead to deforma-
tion of the machine feet fixtures.
Make sure that the forks are evenly loaded when you lift the placement machine.
Use a firm support layer between the forks and the placement machine.
Enlist the help of a second person to watch while you lift the placement machine and
make sure that the placement machine does not tip over to one side.