00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第136页
8 Repairs to SmartFeeder 2x8 mm X 8.3 Side Covers 136 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 8.3.2 Fitting the Left Side Cover ► Carefully place the feeder module with the right- side side down on a stab…
8 Repairs to SmartFeeder 2x8 mm X
8.3 Side Covers
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 135
8.3 Side Covers
Required spare part
Feeder module Item no. Designation
SmartFeeder 2x8 mm X 03078734-xx
03078709-xx
03033796-xx
03010209-xx
Cover plate left assy. /X2x8
Cover plate right /X2x8
RF-SN75-2.5 x 6-9.8
(TORX screws)
ISO 7045 - M2.5 x 6-A2-50-H
(Phillips screws)
Required tools
●
Phillips screwdriver 0.6Nm
●
TORX screwdriver 0.6Nm, size T8
8.3.1 Removing the Left Side Cover
► Carefully place the feeder module with the right-
side side down on a stable, level and clean sur-
face.
► Loosen the screws as shown in the diagram.
1. Red circles show screws, for which you need a
Phillips screwdriver with a torque of 0.6Nm.
2. Blue circles show screws for which you need a
TORX screwdriver with a torque of 0.6Nm.
► Place the side cover down on a clean, safe surface.
NOTICE
Attention: The foil disposal cover is held by the side cover and could fall out!
For greater clarity, we recommend that you loosen the same types of screws together and
then keep them in small, marked bowls.
8 Repairs to SmartFeeder 2x8 mm X
8.3 Side Covers
136 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
8.3.2 Fitting the Left Side Cover
► Carefully place the feeder module with the right-
side side down on a stable, level and clean sur-
face.
► Ensure the foil disposal cover is in place.
► Place the side cover onto the feeder.
► Make sure that the side cover is aligned flush
with the operating panel.
1. Blue circles (RF-SN75-2.5x6-9.8), point to the
screws for which you need a TORX screwdriver
with a torque of 0.6Nm.
2. Red circles show screws (M2.5 x 6), for which
you need a Phillips screwdriver with a torque of
0.6 Nm.
When you tighten the screws, make sure that these are NOT distorted.
NOTICE
When you tighten the screws, make sure that these are NOT distorted.
8.3.3 Removing the Right Side Cover
► Carefully place the feeder module with the left-
hand side down on a stable, level and clean sur-
face.
► Loosen the screws as shown in the diagram.
1. Red circles show screws (M2.5 x 6), for which
you need a Phillips screwdriver with a torque of
0.6 Nm.
2. Blue circles (RF-SN75-2.5x6-9.8), point to the
screws for which you need a TORX screwdriver
with a torque of 0.6Nm.
► Place the side cover down on a clean, safe surface.
NOTICE
Attention: The foil disposal cover is held by the side cover and could fall out!
For greater clarity, we recommend that you loosen the same types of screws together and
then keep them in small, marked bowls.
8 Repairs to SmartFeeder 2x8 mm X
8.4 EDIF
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 137
8.3.4 Fitting the Right Side Cover
► Carefully place the feeder module with the left-
hand side down on a stable, level and clean sur-
face.
► Ensure the foil disposal cover is in place.
► Place the side cover onto the feeder.
► Make sure that the side cover is aligned flush
with the operating panel.
1. Blue circles show screws for which you need a
TORX screwdriver with a torque of 0.6Nm.
2. Red circles show screws, for which you need a
Phillips screwdriver with a torque of 0.6Nm.
NOTICE
When you tighten the screws, make sure that these are NOT distorted.
8.4 EDIF
Required spare part
Fig.44: EDIF secondary assembly X Smart
Feeder module Item no. Designation
SmartFeeder 2x8mmX 03125222Sxx EDIF secondary assembly X Smart
Spare parts also available
Feeder module Item no. Designation
SmartFeeder 2x8 mm X 03012683-xx Pressure spring D-027
03068667-xx Collar screw ø4x4.5 M3 /X2x8
Required tools
●
Flat-bladed screwdriver
●
Phillips screwdriver