00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第166页
8 Repairs to SmartFeeder 2x8 mm X 8.8 Foil rocker 166 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 8.8.2 Additional spare parts for the foil rocker Fig.54: Individual foil rocker parts Feeder module Position …
8 Repairs to SmartFeeder 2x8 mm X
8.8 Foil rocker
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 165
8.8.1.1 Removing the Foil Rocker Cpl.
► Place the feeder on a stable, level and clean sur-
face.
► Remove the left and right side covers. (See 8.3.1
"Removing the Left Side Cover" [}135], 8.3.3
"Removing the Right Side Cover" [}136])
► Remove the tape duct.(1)
► Unplug the photo interrupter cable from the main
board.(2)
► Loosen and remove the TORX screws from the
foil rocker.(3)
► Push the foil rocker to the right(4) and unplug the
cable.(5)
8.8.1.2 Fitting the Foil Rocker Cpl.
► Fasten the new cable at the same positions as
the old cable.(1)
► Connect the cable to the foil rocker connector
and then fit the foil rocker.(2)
► Replace the tape duct, making sure that the
cable is at the bottom.(3)
► Connect the cable to the main board. (4)
► Refit the left and right side covers (see 8.3.2 "Fit-
ting the Left Side Cover" [}136], 8.3.4 "Fitting the
Right Side Cover" [}137]).
8 Repairs to SmartFeeder 2x8 mm X
8.8 Foil rocker
166 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
8.8.2 Additional spare parts for the foil rocker
Fig.54: Individual foil rocker parts
Feeder module Position Item no. Designation
SmartFeeder 2x8mm X 1 03075720-xx Spring pin with spring/X2x8mm
2 03003143-xx Roller /foil disposal X8
3 03067456-xx Roller axis for rocker/X2x8
4 03066482- xx Foil rocker/X2x8
5 03061563-xx Bearing shaft for rocker /X2x8
6 03074758-xx Rocker bearing / X2x8
7 03076204-xx Distance plate 1.7 mm
8 03063457-xx Light barrier transmitter flat assy.
X2x8
9 03033797-xx RF-SN75-2.5 x 8-9.8
Required tools
●
Phillips screwdriver
●
Small flat-bladed screwdriver
●
Tweezers
8 Repairs to SmartFeeder 2x8 mm X
8.8 Foil rocker
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 167
8.8.2.1 Removing the Spring Pin with Spring
► Remove the spring pin with a pair of tweezers.
► Remove the spring pin with spring.
8.8.2.2 Fitting the Spring Pin with Spring
The rocker bearing has 3 different positions for the
spring pin. (1)
The higher you position the spring pin, the greater the
tension on the foil will be.
There are 3 pins in the foil rocker, opposite to these 3
positions, so that the spring can be positioned exactly
over the spring pin. (2)
Select the position you want for the spring pin, de-
pending on the required foil tension.
► Insert the spring onto the pin in the foil rocker
which is vertically opposite to the spring pin posi-
tion you chose.
► Use a pair of tweezers to insert the spring pin into
the chosen position in the rocker bearing.