00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第276页

10 Repairs to SmartFeeder 24 - 104 mm X 10.11 Foil disposal blade 276 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 10.10.1 Replacing the flap ► Carefully place the feeder module with the left side down on a st…

100%1 / 286
10 Repairs to SmartFeeder 24 - 104 mm X
10.10 Foil disposal flap
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 275
► Fasten the side section of the roller with the two
screws marked in the diagram.
Use a T8 TORX screwdriver with 0.6 Nm for this.
► Fit the rocker (see 10.9.1.2 "Fitting the
rocker" [}269]).
10.10 Foil disposal flap
Required spare part
Fig.99: Foil disposal flap assy. and axis flap/foil container
Feeder module Item no. Designation
SmartFeeder 24mm X 03115925- xx
03042171-xx
Foil disposal flap assembly X24Smart
Axis flap /foil container X16-X24
SmartFeeder 32mm X 03120759Sxx
03042484-xx
Foil disposal flap assembly X24Smart
Axis flap /foil container X16-X24
SmartFeeder 44mm X 03120624Sxx
03043382-xx
Foil disposal flap assembly X24Smart
Axis flap /foil container X16-X24
SmartFeeder 56mm X 03120624Sxx
03043382-01
Foil disposal flap assembly X24Smart
Axis flap /foil container X16-X24
SmartFeeder 72mm X 03116832Sxx
03043399-xx
Foil disposal flap assembly X24Smart
Axis flap /foil container X16-X24
SmartFeeder 88mm X 03121026Sxx
03042230-xx
Foil disposal flap assembly X24Smart
Axis flap /foil container X16-X24
SmartFeeder 104mm X 03121156Sxx
03121095-xx
Foil disposal flap assembly X24Smart
Axis flap /foil container X16-X24
Required tools
●
Allen key size 3, 0.6Nm
10 Repairs to SmartFeeder 24 - 104 mm X
10.11 Foil disposal blade
276 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
10.10.1 Replacing the flap
► Carefully place the feeder module with the left
side down on a stable, level and clean surface.
► Remove the right rear side wall (see 10.3.3 "Rear
side wall on the right" [}231])
► Pull the flap straight up and off the spindle.
If needed, you can now take the spindle out of
the base unit and replace it with a new one.
► Push the new flap, as shown, onto the spindle.
► Fit the rear, right side wall (see 10.3.3 "Rear side
wall on the right" [}231]).
During assembly, make sure that the spindle is
correctly inserted into the hole in the side wall.
10.11 Foil disposal blade
Required spare part
Fig.100: Cutter, partition wall
Feeder module Item no. Designation
SmartFeeder 24-104 mm X 0341370Sxx Cutter, partition wall
Required tools
●
TORX screwdriver 0.6Nm, size T8
●
Tweezers
WARNING
Risk of injury
The edge of the blade is very sharp. Make sure that you always use a pair of tweezers
when removing and fitting the blade.
10 Repairs to SmartFeeder 24 - 104 mm X
10.11 Foil disposal blade
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 277
10.11.1 Removing the blade
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Open the flap at the back of the foil container
► Remove the screw fastening the blade.(1)
Use a size 8 TORX screwdriver for this.
► Use a pair of tweezers to pull the blade out of the
holder.(2)
10.11.2 Fitting the blade
► Use a pair of tweezers to insert the blade, as
shown, into the holder .(1)
Caution:
the blade is very sharp!
► Screw the blade tight.(2)
Use an RF2.5x6 screw and a size 8 TORX
screwdriver with 0.6Nm for this.
► Close the flap.