00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第278页

10 Repairs to SmartFeeder 24 - 104 mm X 10.12 Leaf spring 278 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 10.12 Leaf spring Required spare part Fig.101: Leaf spring tape infeed Feeder module Item no. Designa…

100%1 / 286
10 Repairs to SmartFeeder 24 - 104 mm X
10.11 Foil disposal blade
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 277
10.11.1 Removing the blade
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Open the flap at the back of the foil container
► Remove the screw fastening the blade.(1)
Use a size 8 TORX screwdriver for this.
► Use a pair of tweezers to pull the blade out of the
holder.(2)
10.11.2 Fitting the blade
► Use a pair of tweezers to insert the blade, as
shown, into the holder .(1)
Caution:
the blade is very sharp!
► Screw the blade tight.(2)
Use an RF2.5x6 screw and a size 8 TORX
screwdriver with 0.6Nm for this.
► Close the flap.
10 Repairs to SmartFeeder 24 - 104 mm X
10.12 Leaf spring
278 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
10.12 Leaf spring
Required spare part
Fig.101: Leaf spring tape infeed
Feeder module Item no. Designation
SmartFeeder 24mm X 03115906Sxx Leaf spring tape infeed X24Smart
SmartFeeder 32mm X 03117180-xx Leaf spring tape infeed X32Smart
SmartFeeder 44mm X 03120864-xx Leaf spring tape infeed X44Smart
SmartFeeder 56mm X 03120622-xx Leaf spring tape infeed X56Smart
SmartFeeder 72mm X 03116123-xx Leaf spring tape infeed X72Smart
SmartFeeder 88mm X 03121027-xx Leaf spring tape infeed X88Smart
SmartFeeder 104mm X 03121157-xx Leaf spring tape infeed X104Smart
Required tools
●
Phillips screwdriver 0.6Nm
●
TORX screwdriver 0.6Nm, size T8
10.12.1 Replacing the leaf spring
► Carefully place the feeder module with the left
side down on a stable, level and clean surface.
► Remove the right side wall (see 10.3.3 "Rear side
wall on the right" [}231])
► Pull the leaf spring up and out of the feeder mod-
ule base unit.
► Insert the new leaf spring, as shown, into the
base unit.
Make sure that the lower catch for the leaf spring
(marked on the left in the diagram) is outside the
base unit.
► Fasten the right side wall (see 10.3.3 "Rear side
wall on the right" [}231])
10 Repairs to SmartFeeder 24 - 104 mm X
10.13 Handle assembly with control panel
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 279
10.13 Handle assembly with control panel
Required spare part
Fig.102: Handle X24-104 assy.
Feeder module Item no. Designation
SmartFeeder 24 – 104 mm X 03112666Sxx Handle assembly X24-104.
(prefitted with flat ribbon cable)
Required tools
●
Phillips screwdriver 0.6Nm
●
TORX screwdriver size T8, 0.6Nm
●
Tweezers
10.13.1 Removing the handle assembly
► Carefully place the feeder module with the left side down on a stable, level and clean surface.
► Remove the right side wall (see 10.3.3 "Rear side wall on the right" [}231])
► Remove the pressure spring from the rocker (see 10.9.2.1 "Replacing the pressure spring and
spring support" [}271]).
► Carefully place the feeder module with the right side down on a stable, level and clean sur-
face.
► Remove the left side plate (see 10.3.1 "Removing/fitting the left side plate" [}230]).
► Open the bar on the flat ribbon connection on the
control board.(1)
► Unplug the flat ribbon cable form the connec-
tion.(2)