00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第31页
6 Repairs to SmartFeeder 4 mm X 6.3 Side Covers Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 31 6.3.1 Removing the Left Side Cover NOTICE Avoiding damaging the board Before you remove the left side cover, make…
6 Repairs to SmartFeeder 4 mm X
6.3 Side Covers
30 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
6.3 Side Covers
NOTICE
Avoiding damaging the board
To avoid damaging the threaded bolts on the printed circuit board, only remove the side
cover if the other side cover has been fully fitted i.e. with all screws.
Required spare part
Fig.4: Side plate left assy. X8Smart (top), side plate right assy. X8Smart (bottom)
Feeder module Item no. Designation
SmartFeeder 4mmX 03100525Sxx Side plate left assy. X8Smart
03100526Sxx Side plate right assy. X8Smart
03033796-xx
03071822-xx
03023227-xx
03071821-xx
03044543-xx
A
B
C
D
E
Screws:
RF-SN75 2.5 x 6-9.8 (14x)
SN 213307-H-M2.5 x 5-A2-70 (8x)
ISO 7046-2-M2.5 x 5-A2-70-H (4x)
SN 213307-H-M2.5 x 3-A2-70 (2x)
RF-SN85-2.5 x 7.5-9.8 (1x)
Required tools
●
Phillips screwdriver 0.9Nm
●
TORX screwdriver 0.6Nm, size T8
6 Repairs to SmartFeeder 4 mm X
6.3 Side Covers
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 31
6.3.1 Removing the Left Side Cover
NOTICE
Avoiding damaging the board
Before you remove the left side cover, make sure that the right side cover has been com-
pletely fixed in place with all screws. If not, the threaded bolts could be damaged on the
board.
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Loosen the screws as shown in the diagram.
You need a TORX screwdriver for the screws marked
A.
You need a Phillips screwdriver for the screws marked
B, Cand D.
The side cover is only inserted in the upper part of the
frame in the area marked red.
► Pull the side cover down and out.
6.3.2 Fitting the Left Side Cover
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Push the side cover (area marked in red) under
the rail as shown, as far as the stop.
► Fix the screws as shown in the diagram. Begin
with the inner screws and work towards the out-
side.
You need a Phillips screwdriver with 0.9 Nm for the
screws marked B, Cand D.
You need a TORX screwdriver with 0.6 Nm for the
screws marked A.
6 Repairs to SmartFeeder 4 mm X
6.3 Side Covers
32 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
6.3.3 Removing the Right Side Cover
NOTICE
Avoiding damaging the board
Before you remove the right side cover, make sure that the left side cover has been com-
pletely fixed in place with all screws. If not, the threaded bolts could be damaged on the
board.
► Carefully place the feeder module with the left
side down on a stable, level and clean surface.
► First loosen the screw marked D. This screw
fixes the EDIF connector on the main board.
NOTICE!
To avoid damaging the connector, observe the
installation guide after this description for the
right side cover with the relevant torques!
.
► Loosen the screws marked A and E with a TORX
screwdriver.
► Loosen the screws marked B and C with a
Philips screwdriver.
The side cover is only inserted in the upper part of the
frame in the area marked red.
► Pull the side cover down and out.
► Carefully lift the side cover (1).
In the center of the inside, you will find the "motor
cable coupling board", to which two cables are con-
nected.
► Carefully pull the two connectors (2) out of the
connections.
Place the side cover (1) with the board (2) facing up-
wards on a clean and even surface.
Note:
Please note that the foil container cover (3) and the
foil container flap (4) are only clipped or placed on!
Remove these two parts before you change the posi-
tion of the feeder module.
A description of how to remove the cover and the foil
container flap can be found in section 6.12 "Flap/drip
tray for cover foil" [}66].