00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第150页

8 Repairs to SmartFeeder 2x8 mm X 8.7 Drives 150 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 8.7 Drives 8.7.1 Shifted gear for tape drive NOTICE Spare parts kit Due to the potential wear of plastic toothed wh…

8 Repairs to SmartFeeder 2x8 mm X

8.6 Splice sensor / dummy

Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 149

8.6.5.1 Removing the Cable Splice Sensor

► Place the feeder on a stable, level and clean sur-

face.

► Remove the left and right side covers. (See 8.3.1

"Removing the Left Side Cover" [}135], 8.3.3

"Removing the Right Side Cover" [}136])

► Disconnect the connector from the main

board(1).

► Remove the seal band left and right(2).

► Remove the M2.5x6 screw from splice sensor(3)

and disconnect the cables(4).

8.6.5.2 Fitting the Cable Splice Sensor

► Lay the new cables(1).

► Place the seal band left and right level with the

channel. Ensure the cables can move freely.(2).

► Reconnect the cables to the splice sensor(3).

► Refit the splice sensor using the M2 5x6

screw(4).

► Connect the connector to the main board(5).

► Fit the left and right side covers. (See 8.3.2 "Fit-

ting the Left Side Cover" [}136], 8.3.4 "Fitting the

Right Side Cover" [}137])

CAUTION

Ensure the cables are not trapped between housing, splice sensor and covers.

8 Repairs to SmartFeeder 2x8 mm X

8.7 Drives

150 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017

8.7 Drives

8.7.1 Shifted gear for tape drive

NOTICE

Spare parts kit

Due to the potential wear of plastic toothed wheels, it is recommended that, when you find it

necessary to replace one shifted gear or toothed wheel, you also replace the other one.

For this purpose, we recommend the spare parts kit "ETP gear set tape X

2x8mm“ [03095484-xx], which contains both toothed wheels with washers and circlips.

Required spare parts

Fig.47: Spare parts kit "ETP gear set tape X 2x8mm" [03095484-xx]

The spare parts provided in the gear set are listed in the following table:

Feeder module Position Number Item no. Designation

SmartFeeder

2x8mmX

1 03095484-xx ETP drive unit tape X 2x8mm

1 1 03070908-xx Shifted gear 1 tape PA /X2x8

2 1 03070911-xx Toothed wheel 4 tape PA /X2x8

3 2 03083028-xx DIN 988-3x6x0.1-1.4310 (washer)

4 2 00305726-xx DIN 471-3x0.4-C67 (circlip)

5 1 03079902-xx Threaded axis toothed wheel 4 tape / X2x8

In the SmartFeeder 2x8mmX, the toothed wheels for the shifted gear tape drive are fitted in differ-

ent ways.

The drive for the left lane is fitted with the "toothed wheel 4 tape PA /X2x8“ [03070911-xx] with the

"threaded axis toothed wheel 4 tape / X2x8" [03079902-xx]. The "shifted gear 1 tape PA /

X2x8" [03070908-xx], and the "toothed wheel 4 tape PA /X2x8" for the right lane are fitted with

washer and circlip.

The spare parts kit "ETP gear set tape X 2x8mm" [03095484-xx] contains all the parts in the follow-

ing table, in the quantities listed.

Required tools

●

Circlip pliers for outer rings 3-10 mm

●

Allen key 0.35Nm

●

Tweezers

8 Repairs to SmartFeeder 2x8 mm X

8.7 Drives

Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 151

8.7.1.1 Removing the shifted gear 1 tape left/right

► Place the feeder on a stable, level and clean sur-

face.

► Remove the left or right side covers (see 8.3.1

"Removing the Left Side Cover" [}135], 8.3.3

"Removing the Right Side Cover" [}136]).

► Remove the circlip and the washer.(1)

► Remove the toothed wheel.

► Clean the bearing shaft and surroundings.(2)

8.7.1.2 Fitting the shifted gear 1 left / right tape

► Place a small grease film on the shaft (Poly-

lubGLY801).

► Fit the new toothed wheel.(1)

► Fit the washer and circlip(1).

► Lightly grease the circlip.

► Lightly grease between the toothed wheel and

gear motor.

► Fasten the left or right side cover (see 8.3.2 "Fit-

ting the Left Side Cover" [}136], 8.3.4 "Fitting the

Right Side Cover" [}137]).

8.7.1.3 Removing the Toothed Wheel 4 Tape Left

► Place the feeder on a stable, level and clean sur-

face.

► Remove the left and right side covers as appro-

priate . (See 8.3.1 "Removing the Left Side

Cover" [}135], 8.3.3 "Removing the Right Side

Cover" [}136])

► Remove the gear stage 1 tape PA X2x8mm. (See

8.7.1.1 "Removing the shifted gear 1 tape left/

right" [}151])

► Loosen and remove the screw(1).

► Remove the toothed wheel(2).

► Clean the bearing shaft and surroundings(3).