00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第169页
8 Repairs to SmartFeeder 2x8 mm X 8.9 Rocker Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 169 8.9 Rocker 8.9.1 Rocker assembly Required spare part Fig.55: Rocker assembly /X8 Feeder module Item no. Designatio…
8 Repairs to SmartFeeder 2x8 mm X
8.8 Foil rocker
168 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
8.8.2.3 Removing the Cable Photo Interrupter
► Place the feeder on a stable, level and clean sur-
face.
► Remove the left and right side covers. (See 8.3.1
"Removing the Left Side Cover" [}135], 8.3.3
"Removing the Right Side Cover" [}136])
► Remove the tape duct.(1)
► Unplug the photo interrupter cable from the main
board.(2)
► Loosen and remove the TORX screws (RF-
SN75-2.5x8-9.8) from the foil rocker.(3)
► Push the foil rocker to the right(4) and unplug the
cable.(5)
8.8.2.4 Fitting the Cable Photo Interrupter
► Fasten the new cable at the same positions as
the old cable.
► Attach the cable to the foil rocker connector(1)
and fit the foil rocker back into place.(2)
► Replace the tape duct, making sure that the
cable is at the bottom.(3)
► Connect the cable to the main board. (4)
► Refit the left and right side covers (see 8.3.2 "Fit-
ting the Left Side Cover" [}136], 8.3.4 "Fitting the
Right Side Cover" [}137]).
8 Repairs to SmartFeeder 2x8 mm X
8.9 Rocker
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 169
8.9 Rocker
8.9.1 Rocker assembly
Required spare part
Fig.55: Rocker assembly /X8
Feeder module Item no. Designation
SmartFeeder 2x8mmX 03042320Sxx Rocker assembly /X8
03048855-xx Pressure spring 0.75x6.25x31x8.5
03042321-xx Bearing shaft for rocker /X8
Required tools
●
Flat-bladed screwdriver
●
Tweezers
●
Split pin punch size 1.4
8.9.1.1 Removing the Rocker Complete
► Place the feeder module with the left side down
on a stable, level and clean surface.
► Remove the right side cover (see 8.3.3 "Remov-
ing the Right Side Cover" [}136]).
► Remove the pressure springs.(1)
► Screw off the bearing shaft and remove the
rocker.(2)
► Where necessary, unscrew and remove the bear-
ing shaft and then remove the other rocker(3).
8 Repairs to SmartFeeder 2x8 mm X
8.9 Rocker
170 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
8.9.1.2 Fitting the rocker assembly
► Refit the left rocker.
► Insert the right-hand rocker again.
► Reinsert the pressure springs.
► Fit the right side cover (see 8.3.4 "Fitting the Right Side Cover" [}137]).
8.9.2 Spare parts on the rocker
Required spare part
Fig.56: Rocker, tamp wheel and bearing shaft
Feeder module Item no. Designation
SmartFeeder 2x8mmX 03041735-xx Rocker with holder/foil disposal X8
03041017-xx Tamp wheel /rocker X8
03042321-xx Bearing shaft for rocker /X8
Required tools
●
Flat-bladed screwdriver
●
Tweezers
8.9.2.1 Removing the tamp wheel and bearing shaft
► Place the feeder on a stable, level and clean sur-
face.
► Remove the rocker as described in 8.9.1.1 "Re-
moving the Rocker Complete" [}169].
► Screw off the bearing shaft(1) and remove the
tamp wheel.(2)