00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第229页

10 Repairs to SmartFeeder 24 - 104 mm X 10.3 Side covers Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 229 10.2.1 Removing the sliding guide ► Turn the feeder module so that its underside is at the top. ► Remov…

100%1 / 286
10 Repairs to SmartFeeder 24 - 104 mm X
10.2 Rear sliding guide
228 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
10.1.2 Fitting the sliding foil
► Press the sliding foil slightly together.
► Push the sliding foil into the sliding guide, from
the front, as far as the end stop.
► Turn the sliding foil, until the slit can be fully seen
and the sliding foil engages audibly.
10.2 Rear sliding guide
Required spare part
Fig.84: Sliding guide, back
Feeder module Item no. Designation
SmartFeeder 24 – 104mmX 03003994- xx Sliding guide / back L200
03010211-xx ISO 7045 - M2.5 x 10-A2-50-H (4x)
Required tools
●
Phillips screwdriver 0.6Nm
10 Repairs to SmartFeeder 24 - 104 mm X
10.3 Side covers
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 229
10.2.1 Removing the sliding guide
► Turn the feeder module so that its underside is at
the top.
► Remove the 4 marked screws on the sliding
guide.
► Lift the sliding guide upwards and off.
10.2.2 Fitting the sliding guide
► Turn the feeder module so that its underside is at
the top.
► Fit the slide bearing – as illustrated – to the un-
derside of the feeder module.
Observe the arrangement of the drilled holes in
the slide bearing.
► Push the slide bearing, as shown, forward to-
wards the front slide bearing, as far as the stop.
► Now lower the two snap tabs of the slide bearing
into the openings provided on the underside of
the feeder module.
► Use the 4 screws to fix the slide bearing with
0.6Nm to the feeder module.
10.3 Side covers
Required spare parts
Side plate left X24 -104Smart Cover right X24 -104Smart Side wall right X24 -104Smart
Feeder module Item no. Designation
SmartFeeder 24 – 104 mm X 03113301Sxx Side plate left X24 104Smart
03122209Sxx Cover right X24-104Smart
03122209Sxx Side wall right X24-104Smart
Required tools
●
Phillips screwdriver 0.6Nm
●
TORX screwdriver 0.6Nm, size T8
10 Repairs to SmartFeeder 24 - 104 mm X
10.3 Side covers
230 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
10.3.1 Removing/fitting the left side plate
► Carefully place the feeder module with the right side down on a stable, level and clean sur-
face.
► Loosen or fasten the screws with the tool specified in the diagram.
The different screw types are color-coded in the diagram.
●
Blue dots mark those screws for which you need to use a TORX screwdriver with 0.6Nm.
Screw: RF-SN75-2.5 x 6-9.8 [03033796-xx].
●
Red dots mark those screws for which you need to use a Phillips screwdriver with 0.6Nm.
Screw: SN 213307-H-M2.5 x 5-A2-70 [03071822-xx]
► During assembly of the side wall, make
sure that the two nibs on the leaf spring
are outside the base unit and that the leaf
spring can swing downwards without ob-
struction.