00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第163页

8 Repairs to SmartFeeder 2x8 mm X 8.7 Drives Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 163 8.7.3.2 Fitting the hybrid stepping motor assembly NOTICE The installation procedure is the same for the left and r…

100%1 / 286
8 Repairs to SmartFeeder 2x8 mm X
8.7 Drives
162 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
8.7.3 Hybrid stepping motor assembly left / right
Required spare part
Fig.50: Hybrid stepping motor assembly
Feeder module Item no. Designation
SmartFeeder 2x8mmX 03057582-xx Hybrid stepping motor assembly
Required tools
●
TORX screwdriver 0.6Nm, size T8
●
Phillips screwdriver 0.9Nm
●
Gauge for tape drive motor /X2x8, item no. 03080225-xx
●
Gauge for foil drive /X2x8, item no. 03080235-xx
8.7.3.1 Removing the hybrid stepping motor assy.
NOTICE
The removal procedure is the same for the left and right lane.
This section describes the removal of the hybrid stepping motor on the left side (lane 1).
The removal procedure for the hybrid stepping motor on the right side (lane 2) is the same,
except that it is laterally reversed.
► Place the feeder module with the right side down on a stable, level and clean surface.
► Remove the left side cover (see 8.3.1 "Removing the Left Side Cover" [}135]).
► Remove the shifted gear tape (see 8.7.1.1 "Removing the shifted gear 1 tape left/right" [}151]).
► Remove the two screws marked in the diagram.(1)
► Remove the plug of the motor cable from the main board.(2)
► Remove the motor and cable.
8 Repairs to SmartFeeder 2x8 mm X
8.7 Drives
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 163
8.7.3.2 Fitting the hybrid stepping motor assembly
NOTICE
The installation procedure is the same for the left and right lane.
This section describes the installation of the hybrid stepping motor on the left side (lane 1).
The installation procedure for the hybrid stepping motor on the right side (lane 2) is the
same, except that it is laterally reversed.
Fig.51: Overview of connections on the control board
1. Tape drive left lane (lane 1) 3. Foil drive left lane (lane 1)
2. Tape drive right lane (lane 2) 4. Foil drive right lane (lane 2)
► Place the hybrid stepping motor in position and run the cable through the housing.
► Fit the gauge for the tape motor(1).
► Use the two Phillips screws marked in the diagram to fasten the motor to 0.9Nm. (2)
► Remove the gauge.
► Plug the motor cable connector into the relevant connection on the control board e.g. for the
foil drive of the left lane (lane 1).(3)
Select the connection which matches the motor from the "Overview of connections on the
control board" shown above.
► Refit the shifted gear (see 8.7.1.2 "Fitting the shifted gear 1 left / right tape" [}151]).
► Fasten the left side covers (see 8.3.2 "Fitting the Left Side Cover" [}136]).
8 Repairs to SmartFeeder 2x8 mm X
8.8 Foil rocker
164 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
8.8 Foil rocker
8.8.1 Foil rocker assembly
Required spare part
Fig.52: Foil rocker assembly
Fig.53: Cable light barrier transmitter
Feeder module Item no. Designation
SmartFeeder 2x8mmX 03066480-xx
03063591-xx
Foil rocker assembly /X2x8
Cable light barrier transmitter
Required tools
●
TORX screwdriver 0.6Nm, size T8
●
Small flat-bladed screwdriver