Service Manual SIPLACE SmartFeeder.pdf - 第105页
7 Repairs to SmartFeeder 8 mm X / Xi 7.4 EDIF Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 105 7.4 EDIF Spare part required Fig.31: EDIF secondary assembly Feeder module…
7 Repairs to SmartFeeder 8 mm X / Xi
7.3 Side Covers
104 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
7.3.4 Fitting the right side cover
NOTICE!
Observe the correct position of the foam
seal. Make sure that the foam seal does not
get trapped in the empty tape duct or pro-
trude into it!
.
To check the correct position of the foam seal, remove
the left side cover, as shown (after fitting the right side
cover), and correct the position of the foam rubber if
necessary.
NOTICE!
Please make sure that the foil container
cover (1) and the foil container flap (2) are
correctly clipped on or placed on!
.
A description of how to fit the cover and the foil con-
tainer flap can be found in section 7.12.2
"Fitting the
Flap" [}148].
► Carefully place the feeder module with the left
side down on a stable, level and clean surface.
► Insert the side cover (in the area marked red), as
shown, under the rail, as far as the stop.
► Insert the side cover on the right side, in the area
marked yellow under the encoder.
► Fasten the screws as shown in the diagram. Be-
gin with the inner screws (C
) and work outwards
(B
+ A).
Fasten screw E
last
You need a Phillips screwdriver with 0.6 Nm for the
screws marked B
and C.
You need a TORX screwdriver with 0.6 Nm for the
screws marked A
.
Also use a TORX screwdriver for the screw marked E.
CAUTION!
Tighten screw E no more than hand-tight,
otherwise the screw fixtures inside the feeder
module could be damaged or broken.
.
7 Repairs to SmartFeeder 8 mm X / Xi
7.4 EDIF
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 105
7.4 EDIF
Spare part required
Fig.31: EDIF secondary assembly
Feeder module Item no. Designation
SmartFeeder 8mmX (V1) 00141370-01
SmartFeeder 8mm X Splice (V1) 00141390-01
03101192Sxx EDIF secondary assembly X8S-
mart
SmartFeeder 8mmX (V2) 00141370-02
SmartFeeder 8mm X Splice (V2) 00141390-02
03127518- EDIF secondary assembly X8S-
mart
SmartFeeder 8mm Xi 00141480-xx
SmartFeeder 8mm Xi Splice 00141500-xx
03127518-xx EDIF secondary assembly X8S-
mart
Other spare parts:
Feeder module Item no. Designation
All feeder modules mentioned in the above
table
03012683-xx
03050957-xx
Pressure spring D-027
Collar screw D4x3.15 M3
Tools required
●
Flat-bladed screwdriver 0.9Nm
●
Phillips screwdriver 0.9Nm
●
TORX screwdriver 0.6Nm, size T8
7 Repairs to SmartFeeder 8 mm X / Xi
7.4 EDIF
106 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
7.4.1 Removing the EDIF
► Carefully place the feeder module with the left
side down on a stable, level and clean surface.
► On the right side plate, only remove screwD, in
order to release the EDIF connector in the feeder
module
► Remove the left side cover (see section 7.3.1
"Removing the Left Side Cover" [}102]).
► Pull the EDIF connector(1) straight up and off
the board.
► Loosen the two collar screws on the EDIF.(2)
► Remove the EDIF.(3)
► Remove the two pressure springs.(4)