Service Manual SIPLACE SmartFeeder.pdf - 第177页

8 Repairs to SmartFeeder 2x8 mm X / Xi 8.4 EDIF Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 177 8.4 EDIF Spare part required Fig.57: EDIF secondary assembly X Smart Fee…

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.3 Side Covers

176 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

8.3.4 Fitting the Right Side Cover

► Carefully place the feeder module with the left-

hand side down on a stable, level and clean sur-

face.

► Ensure the foil disposal cover is in place.

► Place the side cover onto the feeder.

► Make sure that the side cover is aligned flush

with the operating panel.

1. Blue circles show screws for which you need a

TORX screwdriver with a torque of 0.6Nm.

2. Red circles show screws, for which you need a

Phillips screwdriver with a torque of 0.6Nm.

NOTICE

When you tighten the screws, make sure that these are NOT distorted.

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.4 EDIF

Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 177

8.4 EDIF

Spare part required

Fig.57: EDIF secondary assembly X Smart

Feeder module Item no. Designation

SmartFeeder 2x8mmX

SmartFeeder 2x8mmXi

03125222Sxx EDIF secondary assembly X Smart

Spare parts also available

Feeder module Item no. Designation

SmartFeeder 2x8 mm X

SmartFeeder 2x8mmXi

03012683-xx Pressure spring D-027

03068667-xx Collar screw ø4x4.5 M3 /X2x8

Tools required

●

Flat-bladed screwdriver

●

Phillips screwdriver

8.4.1 Removing the EDIF – secondary assembly X Smart

► Place the feeder on a stable, level and clean sur-

face.

► Remove the left side cover (see 8.3.1 "Removing

the Left Side Cover" [}174]).

► Loosen and remove the two collar screws(1).

► Loosen and remove the Phillips screw(2).

► Carefully lift the connector from the main

board(3)

► Remove any foam seals present (4).

► Check the pressure springs for damage and re-

place where necessary(5)

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.4 EDIF

178 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

8.4.2 Fitting the EDIF – secondary assembly X Smart

► Insert the two pressure springs(1) into the ducts

provided.

If the pressure springs are bent, these will need

to be replaced.

 NOTICE!

During insertion, make sure that the two

pressure spring point forwards, to the EDIF

and are not distorted.

► Push the EDIF(2) into the recess at the front of

the feeder module.

► Fasten the EDIF with the two collar screws.

► Check whether the EDIF springs back to the front

if slight pressure is applied to it.

If the EDIF does not spring back, loosen the two collar

screws(2)

and make sure that the two pressure

springs(see 1 previous figure) are aligned towards the

front and are not bent.

► Place the connector on the main board, ensuring

the alignment pins are centered(3)

► Fix the connector to the board with the Phillips

screw and carefully tighten.

► Fit the left side cover (see 8.3.2 "Fitting the Left

Side Cover" [}175]).