Service Manual SIPLACE SmartFeeder.pdf - 第124页

7 Repairs to SmartFeeder 8 mm X / Xi 7.7 Drives 124 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 7.7.1.1 Removing the Foil Disposal Motor ► Carefully place the feeder mod…

100%1 / 246
7 Repairs to SmartFeeder 8 mm X / Xi
7.7 Drives
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 123
7.7 Drives
7.7.1 Foil motor
Required spare part
Fig.37: Motor coupling/foil disposal X-Series
NOTICE
Observe the function status of the feeder module
The SmartFeeder 8mmX motors have been converted from the 8 bit encoder to the 12 bit
encoder.
The feeder module firmware is able to supply the 8 bit and the 12 bit encoder. However, the
SmartFeeder 8 mm X can only operate either the 8 bit or the 12 bit motors.
For this reason, when replacing the motor of the foil disposal unit, pay attention to the func-
tion state (FS) of the feeder module and select the spare part which corresponds with it.
Feeder module Position Item no. Designation
SmartFeeder 8 mm X
00141370-xx (up to FS 02
)
1 03119123Sxx Motor assembly for foil disposal X8Smart
(8 bit)
SmartFeeder 8 mm X
00141370-xx (> FS 02
)
SmartFeeder 8 mm Xi
1 03170813-xx Motor for foil drive with 12 bit encoder
SmartFeeder 8mm X
SmartFeeder 8 mm Xi
2
3
4
03028610-xx
03012488-xx
03042536-01
Bearing block, ceramic
SN 213307-H-M2 x 2.5-A2
(for fitting the bearing block)
ISO 4762 - M 2.5 x 12-A2-70
(for fitting the motor)
Tools required
●
Phillips screwdriver 0.9Nm
●
Flat-bladed screwdriver size 3
●
TORX screwdriver 0.6Nm, size T8
●
Angled Allen key, size 2
●
Allen key 0.9 Nm, size 4
●
Tweezers
Required consumables
●
Grease Klübersynth GE 14-151
7 Repairs to SmartFeeder 8 mm X / Xi
7.7 Drives
124 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
7.7.1.1 Removing the Foil Disposal Motor
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Remove the left side cover (see 7.3.1 "Removing
the Left Side Cover" [}102]).
► Remove the 3 Phillips screws(1) marked in the
diagram from the bearing cap for the foil gear.
► Lift the bearing cap(2) up with a pair of tweezers
or a small screwdriver(3)
and remove it.
► Loosen the spiral gear(4) on the foil disposal
with a size 4 Allen key(5)
.
7 Repairs to SmartFeeder 8 mm X / Xi
7.7 Drives
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 125
► Move the feeder module to an upright and stable
position.
On the right-hand side of the feeder module you can
access the bearing screw (6)
for the spiral gear.
► On the left-hand side of the feeder module, you
can hold the spiral gear(4)
, while on the right-
hand side, you can open the connection using a
size 3 flat-bladed screwdriver(7)
.
► Pull the spiral gear(4) off completely.
► Remove the two screws(8), with which the
ceramic bearing blocks(9)
are fixed on the other
side.
► Turn the feeder module on to its right side.
► Open the two screws(10), with which the motor
is fastened. Use a size 2 angled Allen key for
this.
► Use a pair of tweezers to pull the outer bearing
block(11)
off the motor shaft.