Service Manual SIPLACE SmartFeeder.pdf - 第179页
8 Repairs to SmartFeeder 2x8 mm X / Xi 8.5 Pickup window Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 179 8.5 Pickup window NOTICE Conversion to the new version SmartFeed…
8 Repairs to SmartFeeder 2x8 mm X / Xi
8.4 EDIF
178 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
8.4.2 Fitting the EDIF – secondary assembly X Smart
► Insert the two pressure springs(1) into the ducts
provided.
If the pressure springs are bent, these will need
to be replaced.
NOTICE!
During insertion, make sure that the two
pressure spring point forwards, to the EDIF
and are not distorted.
.
► Push the EDIF(2) into the recess at the front of
the feeder module.
► Fasten the EDIF with the two collar screws.
► Check whether the EDIF springs back to the front
if slight pressure is applied to it.
If the EDIF does not spring back, loosen the two collar
screws(2)
and make sure that the two pressure
springs(see 1 previous figure) are aligned towards the
front and are not bent.
► Place the connector on the main board, ensuring
the alignment pins are centered(3)
.
► Fix the connector to the board with the Phillips
screw and carefully tighten.
► Fit the left side cover (see 8.3.2 "Fitting the Left
Side Cover" [}175]).
8 Repairs to SmartFeeder 2x8 mm X / Xi
8.5 Pickup window
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 179
8.5 Pickup window
NOTICE
Conversion to the new version SmartFeeder 2x8mm Xi
The pickup area of the old and the new version of the pickup window are not compatible
with one another!
On introduction of the "SIPLACE SmartFeeder 2x8mm Xi" and "SIPLACE SmartFeeder 2x8mm Xi
Splice" feeder modules, the "SIPLACE SmartFeeder 2x8mm X" and "SIPLACE SmartFeeder
2x8mm X Splice Sensor" feeder modules have been discontinued.
At the same time, the new pickup window for the SmartFeeder 2x8mm Xi has also been introduced
as a spare part for the discontinued SmartFeeder 2x8mm X.
The individual parts of the pickup area in the old and new version are not compatible with one an-
other! If you want to replace individual spare parts (pickup window, pressure fork, tape duct) in
these feeder modules, you will need to completely upgrade the pickup areas of both tracks to the
new version.
In order to upgrade both feeder module tracks, you need 2x the spare part " Tape cutter with
pickup window /X2x8 V2" [03145735-xx].
The following section describes replacement of the individual parts in the new pickup area. To en-
sure that the parts from the old and new version are not confused with one another, pay attention
to the marking shown below on the SmartFeeder 2x8mm Xi pickup area parts.
Fig.58: Markings on SmartFeeder 2x8mm Xi spare parts
Feeder module SIPLACE SmartFeeder 2x8mm X, [00141269-xx]
SIPLACE SmartFeeder 2x8mm X splice sensor, [00141289-xx]
Spare parts
(no longer available)
Tape duct /X2x8 [03077354-xx]
Rocker lever /X2x8 [03053708-xx]
Collar screw /X2x8 [03077823-xx]
Pickup window assy. /X2x8 [03078710-xx]
Tape duct with pickup window /X2x8 V2 [03145735-xx]
Spare part
(Conversion package)
Tape duct with pickup window /X2x8 V2 [03145735-xx]
8 Repairs to SmartFeeder 2x8 mm X / Xi
8.5 Pickup window
180 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
Spare part required
Fig.59: Pickup window assy. SmartFeeder 2x8 mm Xi
Feeder module Position Item no. Designation
SmartFeeder 2x8 mm Xi 1, 3, 4, 6, 7 03145735-xx Tape duct with pickup window /X2x8
V2
1 03145734-xx Tape duct, prefitted /X2x8 V2
3 03145733-xx Pickup window assy. /X2x8 V2
4 00349254-xx Fitting screw
6 03077394-xx Axis pickup window /X2x8
7 03165452-xx Pressure fork /X2x8 tilt function
2 03010210-xx ISO 7045 - M2.5 x 8-A2-50-H
5 03010214-xx ISO 7045 - M2.5 x 16-A2-50-H
8 03077928-xx Pressure spring 0.85x5.1x18.3
Tools and consumables required
●
Phillips screwdriver
●
Tweezers
●
Allen key 1.5
●
Grease Klubersynt GE 14-151 tub 45g, item no. 03005735-01