Service Manual SIPLACE SmartFeeder.pdf - 第173页

8 Repairs to SmartFeeder 2x8 mm X / Xi 8.2 Rear Sliding Guide Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 173 8.2 Rear Sliding Guide Spare part required Fig.56: Rear sl…

100%1 / 246
8 Repairs to SmartFeeder 2x8 mm X / Xi
8.1 Front sliding guide/sliding foil
172 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
8.1 Front sliding guide/sliding foil
Spare part required
Fig.55: Sliding foil X-Feeder
Feeder module Item no. Designation
SmartFeeder 2x8mmX
SmartFeeder 2x8mmXi
03019604Sxx Front sliding guide
Tools required
●
Sliding foil remover
8.1.1 Removing the Sliding Foil
► Place the feeder on a stable, level and clean sur-
face.
► Insert the sliding foil remover into the sliding
guide.(1)
► Lever the sliding foil out of the engaged position.
► Lever the sliding foil until it has been turned by
approximately90°.
► Push the sliding foil towards the front and out of
the sliding guide.(2)
8.1.2 Fitting the Sliding Foil
► Press the sliding foil slightly together.
► Push the sliding foil from the front into the sliding guide, until it engages.
8 Repairs to SmartFeeder 2x8 mm X / Xi
8.2 Rear Sliding Guide
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 173
8.2 Rear Sliding Guide
Spare part required
Fig.56: Rear sliding guide L200
Feeder module Item no. Designation
SmartFeeder 2x8mmX
SmartFeeder 2x8mmXi
03003994Sxx Rear sliding guide L200
03010209-xx ISO 7045 - M2.5 x 6-A2-50-H
Tools required
●
Phillips screwdriver 0.6Nm
8.2.1 Removing the Rear Sliding Guide
► Place the feeder on a stable, level and clean sur-
face.
► Loosen the 4 screws(1) on the sliding guide.
► Lift the sliding guide up at the back and pull
upwards and off.
8.2.2 Fitting the Rear Sliding Guide
► Push the left part of the rear sliding guide as far as possible towards the front sliding guide,
and into the recess.
► Now lower the two snap tabs of the guiding slide into the openings provided on the underside
of the feeder module.
► Screw the sliding guide onto the bottom of the feeder module. Use the 03010209-xx ISO7045
- M2.5x 6-A2-50-H screws for this.
CAUTION
► To prevent damage to the pin wheel, make sure that the pickup window is fitted for
this work.
8 Repairs to SmartFeeder 2x8 mm X / Xi
8.3 Side Covers
174 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
8.3 Side Covers
Spare part required
Feeder module Item no. Type Designation
SmartFeeder 2x8 mm X
SmartFeeder 2x8mmXi
03078734-xx Cover plate left assy. /X2x8
03078709-xx Cover plate right /X2x8
03010209-xx 1 ISO 7045 - M2.5 x 6-A2-50-H
(Phillips screws)
03033796-xx 2 RF-SN75-2.5 x 6-9.8
(TORX screws)
Tools required
●
Phillips screwdriver 0.6Nm
●
TORX screwdriver 0.6Nm, size T8
8.3.1 Removing the Left Side Cover
► Carefully place the feeder module with the right-
side side down on a stable, level and clean sur-
face.
► Loosen the screws as shown in the diagram.
1. Red circles show screws, for which you need a
Phillips screwdriver with a torque of 0.6Nm.
2. Blue circles show screws for which you need a
TORX screwdriver with a torque of 0.6Nm.
► Place the side cover down on a clean, safe surface.
NOTICE
Attention: The foil disposal cover is held by the side cover and could fall out!
For greater clarity, we recommend that you loosen the same types of screws together and
then keep them in small, marked bowls.