Service Manual SIPLACE SmartFeeder.pdf - 第96页

6 Repairs to SmartFeeder 4 mm X / Xi 6.17 Foil container 96 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

6 Repairs to SmartFeeder 4 mm X / Xi

6.17 Foil container

Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 95

► Insert the pressure spring back into the rocker.

► Carefully place the feeder module with the left

side down on a stable, level and clean surface.

► Remove the screws marked in the diagram.

You need a Phillis screwdriver for the screws marked

(1)

and (2).

Use a size T8 TORX screwdriver for the screw at (3).

► Carefully place the feeder module with the left

side down on a stable, level and clean surface.

► Inserting the (new) insertion foil container.

► Fasten the insertion foil container with the 4

TORX screws marked in the diagram

(RF‑SN75‑2.5 x 6‑9.8, 03033796‑xx).(1)

Use a TORX screwdriver 0.6Nm, size T8 for this.

► Fasten the Phillips screw (ISO 7045 - M2.5 x 6-

A2-50-H, 03010209‑xx).(2)

► Insert the shaft in the position shown into the in-

sertion foil container, as far as the stop.(3)

► Push the flap onto the shaft.(3)

► Fit the right side cover (see6.3.4 "Fitting the Right

Side Cover" [}32]).

► Fasten the back slide guide (see 6.2.2 "Fitting the

Sliding Guide" [}28]).

6 Repairs to SmartFeeder 4 mm X / Xi

6.17 Foil container

96 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

7 Repairs to SmartFeeder 8 mm X / Xi



Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 97

7 Repairs to SmartFeeder 8 mm X / Xi

Feeder module Item no. Description

SmartFeeder 8mmX 00141370-xx

00141390-xx

SIPLACE SmartFeeder 8mm X

SIPLACE SmartFeeder 8mm X splice sensor

SmartFeeder 8 mm Xi 00141480-xx

00141500-xx

SIPLACE SmartFeeder 8mm Xi

SIPLACE SmartFeeder 8mm Xi splice sensor

Notes about SmartFeeder Xi

The SmartFeederXi feeder modules support high infeed speeds for maximum utilization of the

machine placement capacity with the SIPLACE SpeedStar CP20P2 placement head.

The corrugated slide on the back of the SmartFeeder is a clear identifying feature of the Smart-

Feeder Xi.

SIPLACE Pro shows the SmartFeederXi as a SmartFeederX. If a CP20P2 head is used in the

setup, SIPLACE Pro automatically assumes that a SmartFeederXi is being used. The maximum

speed of a SmartFeederXi depends on the placement head which uses this feeder module.

The station software also shows a SmartFeederXi as a SmartFeederX. If a faster SmartFeederXi

is needed for performance purposes (machine with CP20P2 head), although a slower Smart-

FeederX is configured, the feeder LED will flash briefly, to signal the status "Not fast enough". The

station software will mark this feeder orange with the status "Too slow".

The SmartFeeder 8mmXi feeder module can be operated at any machine which can already ac-

commodate the SmartFeeder 8mmX. Due to the shift of the pickup position, there is an incompat-

ibility with older software versions. For this reason, the following station software versions are re-

quired:

●

≥ SIRIO 707.1SP2.HF9

●

≥ 605.03 SP5 + HF9

For more information about introducing the SmartFeederXi, refer to the technical information "In-

troducing the SmartFeeder modules Xi" (German [TI2018-09D14], English [TI201809E14]).