Service Manual SIPLACE SmartFeeder.pdf - 第146页
7 Repairs to SmartFeeder 8 mm X / Xi 7.11 Wiper 146 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 7.11.1 Removing the stripping device 8 mm X ► Carefully place the feeder …
7 Repairs to SmartFeeder 8 mm X / Xi
7.11 Wiper
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 145
7.11 Wiper
Required spare part
Fig.45: Wiper for foil disposal X8Smart
Feeder module Item no. Designation
SmartFeeder 8mm X
SmartFeeder 8 mm Xi
03106790Sxx Wiper for foil disposal X8Smart
03071821-xx SN 213307-H-M2.5 x 3-A2-70
Tools required
●
Phillips screwdriver, small
●
Tweezers
7 Repairs to SmartFeeder 8 mm X / Xi
7.11 Wiper
146 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
7.11.1 Removing the stripping device 8 mm X
► Carefully place the feeder module with the left side
down on a stable, level and clean surface.
► Insert the Phillips screwdriver through the opening in
the rocker(1)
.
► Remove the Phillips screw(2), which is fastening the
stripping device.
► Press the rocker(3) backwards.
► Pull the stripping device(4) upwards.
► Lower the rocker again.
► Remove the stripping device.
7.11.2 Fitting the stripping device 8 mm X
► Press the rocker(1) backwards.
► Insert the stripping device(2) as shown, with the flat
side facing upwards.
► Align the stripping device so that it is straight.
Make sure that the hole for the screw is visible through
the hole in the stripping device and that the individual
parts of the stuffing gear protrude through the recesses
(3)
of the stripping device.
► Lower the rocker again.
► Use a pair of tweezers to hold the Phillips screw(4)
over the drilled hole.
► Insert the Phillips screwdriver through the opening in
the rocker(5)
.
► Hand-tighten the Phillips screw fastening the strip-
ping device.
7 Repairs to SmartFeeder 8 mm X / Xi
7.12 Foil disposal flap
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 147
7.12 Foil disposal flap
Required spare part
Fig.46: Flap for foil stuffing unit assy. X8Smart
Feeder module Item no. Designation
SmartFeeder 8mmX
SmartFeeder 8 mm Xi
03107505-xx Flap for foil stuffing unit assy. X8Smart
03004081-xx Shaft for D2 foil flap X8
Tools required
●
Phillips screwdriver 0.9Nm
●
TORX screwdriver 0.6Nm, size T8
7.12.1 Removing the Flap
NOTICE
Avoid confusing the foil tank panel
The foil tank panel has a barcode which uniquely identifies the feeder module. Make sure
that this sheet is not confused with another foil tank panel.
► Carefully place the feeder module with the left
side down on a stable, level and clean surface.
► Remove the right side cover (see 7.3.3 "Remov-
ing the right side cover" [}103])
► Carefully lift the foil tank panel(1) out of the base
of the feeder module.