Service Manual SIPLACE SmartFeeder.pdf - 第25页

6 Repairs to SmartFeeder 4 mm X / Xi  Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 25 6 Repairs to SmartFeeder 4 mm X / Xi Feeder module Item no. Description SmartFeeder…

5 Diagnosis and Solutions

5.1 Assignment of Symptoms/Repairs

24 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

Rocker

The rocker is bent.

The plain tamp wheel for the rocker has jammed.

The thread of the bearing shaft is worn.

Replace the rocker assembly

The plain tamp wheel for the rocker is worn or dam-

aged.

Replace the plain tamp wheel

The bearing shaft of the rocker is rough-running or

damaged.

The slit in the bearing shaft is damaged.

Replace the rocker bearing shaft

Control panel

The display window, an LED lamp or a button is de-

fective.

The removal handle is defective or does not engage

properly.

Replace the control panel assembly

Leaf spring

The leaf spring on the tape inlet is missing or bent. Replace the leaf spring

6 Repairs to SmartFeeder 4 mm X / Xi



Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 25

6 Repairs to SmartFeeder 4 mm X / Xi

Feeder module Item no. Description

SmartFeeder 4mmX 00141368-xx SIPLACE SmartFeeder 4mm X

SmartFeeder 4mm Xi 00141478-xx SIPLACE SmartFeeder 4mm Xi

00141498-xx SIPLACE SmartFeeder 4mm Xi splice sensor

Notes about SmartFeeder Xi

The SmartFeederXi feeder modules support high infeed speeds for maximum utilization of the

machine placement capacity with the SIPLACE SpeedStar CP20P2 placement head.

The corrugated slide on the back of the SmartFeeder is a clear identifying feature of the Smart-

Feeder Xi.

SIPLACE Pro shows the SmartFeederXi as a SmartFeederX. If a CP20P2 head is used in the

setup, SIPLACE Pro automatically assumes that a SmartFeederXi is being used. The maximum

speed of a SmartFeederXi depends on the placement head which uses this feeder module.

The station software also shows a SmartFeederXi as a SmartFeederX. If a faster SmartFeederXi

is needed for performance purposes (machine with CP20P2 head), although a slower Smart-

FeederX is configured, the feeder LED will flash briefly, to signal the status "Not fast enough". The

station software will mark this feeder orange with the status "Too slow".

The SmartFeeder 4mmXi feeder module can be operated at any machine which can already ac-

commodate the SmartFeeder 4mmX. The SmartFeeder 4mmXi can also be operated with older

station software versions 7xx.x.

For more information about introducing the SmartFeederXi, refer to the technical information "In-

troducing the SmartFeeder modules Xi" (German [TI2018-09D14], English [TI201809E14]).

6 Repairs to SmartFeeder 4 mm X / Xi

6.1 Front sliding guide/sliding foil

26 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

6.1 Front sliding guide/sliding foil

Required spare part

Fig.2: Sliding foil

Feeder module Item no. Designation

SmartFeeder 4mmX

SmartFeeder 4 mm Xi

03019604Sxx Sliding foil, X-feeder JUM-S-06LY

Tools required

●

Sliding foil remover

6.1.1 Removing the Sliding Foil

► Place the feeder module carefully down on its

side, onto a stable, level and clean surface.

► Place the sliding foil remover into the sliding

guide, as shown in the diagram.

► Lever the sliding foil out of the engaged position.

► Pull the sliding foil out of the sliding guide, to-

wards the front.

6.1.2 Fitting the Sliding Foil

► Press the sliding foil slightly together.

► Push the sliding foil into the sliding guide, from

the front, as far as the end stop.

► Turn the sliding foil, until the slit can be fully seen

and the sliding foil engages audibly.