Service Manual SIPLACE SmartFeeder.pdf - 第129页
7 Repairs to SmartFeeder 8 mm X / Xi 7.8 Foil rocker Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 129 7.8 Foil rocker 7.8.1 Foil rocker assembly Spare part required Fig.…
7 Repairs to SmartFeeder 8 mm X / Xi
7.7 Drives
128 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
► Turn the feeder module onto the other side.
► Fasten the bearing blocks with the two Phillips
screws(9)
(hand-tight).
► If necessary, correct the position of the bearing
blocks.
► Make sure that the spiral gear only has grease on
the small toothed wheel and that the large
toothed wheel is free of grease. You may need to
remove any grease on the larger toothed wheel!
► Place the feeder module in a stable, upright posi-
tion.
► Insert the spiral gear(10) into the hole provided,
with the smaller toothed wheel at the front. Make
sure that the small toothed wheel of the spiral
gear engages properly with the worm gear of the
motor.
► Fasten the spiral gear (hand-tight) with the bear-
ing screw(11)
. Use a flat-bladed screwdriver to
help you.
► Tighten the left-hand side of the spiral gear(12)
with a size 4 Allen key(13) and 0.9 Nm.
► Fit the bearing cap(14) onto the foil stripping
unit, as shown.
► Fasten the bearing cap with the three marked
screws ISO 7046-2-M2.5x 6-A2-70-H (item no
03023228-xx)(15)
, using a Phillips screwdriver
and 0.9Nm.
► Fasten the left side cover (see 7.3.2 "Fitting the
left side cover" [}102]).
7 Repairs to SmartFeeder 8 mm X / Xi
7.8 Foil rocker
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 129
7.8 Foil rocker
7.8.1 Foil rocker assembly
Spare part required
Fig.38: Foil rocker assembly
Fig.39: Cable light barrier emitter
Feeder module Item no. Designation
SmartFeeder 8mm X
SmartFeeder 8 mm Xi
03101471Sxx
03063591-xx
Foil rocker assembly /X8Smart
Cable for light barrier emitter 2x8
Tools required
●
Flat-bladed screwdriver size 1 or tweezers
●
TORX screwdriver size T8
7 Repairs to SmartFeeder 8 mm X / Xi
7.8 Foil rocker
130 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
7.8.1.1 Removing the Foil Rocker Assembly
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Remove the two screws(1) which fasten the foil
rocker.
Use a size T8 TORX screwdriver for this.
► Pull the foil rocker up and off(2).
► Make sure that the flat ribbon cable(3) is not
stretched too much.
► Turn the foil rocker into the position shown in the
diagram.
► Swing the holder on the flat ribbon connection
up(4).
► Pull the flat ribbon cable(5) out of the flat ribbon
cable connection.