Service Manual SIPLACE SmartFeeder.pdf - 第171页

8 Repairs to SmartFeeder 2x8 mm X / Xi  Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 171 8 Repairs to SmartFeeder 2x8 mm X / Xi Feeder module Item no. Description SmartF…

7 Repairs to SmartFeeder 8 mm X / Xi

7.17 Foil container

170 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

8 Repairs to SmartFeeder 2x8 mm X / Xi



Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 171

8 Repairs to SmartFeeder 2x8 mm X / Xi

Feeder module Item no. Description

SmartFeeder 2x8mmX 00141269-xx SIPLACE SmartFeeder 2x8 mm X

00141289-xx SIPLACE SmartFeeder 2x8mm X splice sensor

SmartFeeder 2x8 mm X 00141479-03 SIPLACE SmartFeeder 2x8mm Xi

00141499-03 SIPLACE SmartFeeder 2x8mm Xi splice

Notes about SmartFeeder Xi

The SmartFeederXi feeder modules support high infeed speeds for maximum utilization of the

machine placement capacity with the SIPLACE SpeedStar CP20P2 placement head.

The corrugated slide on the back of the SmartFeeder is a clear identifying feature of the Smart-

Feeder Xi.

SIPLACE Pro shows the SmartFeederXi as a SmartFeederX. If a CP20P2 head is used in the

setup, SIPLACE Pro automatically assumes that a SmartFeederXi is being used. The maximum

speed of a SmartFeederXi depends on the placement head which uses this feeder module.

The station software also shows a SmartFeederXi as a SmartFeederX. If a faster SmartFeederXi

is needed for performance purposes (machine with CP20P2 head), although a slower Smart-

FeederX is configured, the feeder LED will flash briefly, to signal the status "Not fast enough". The

station software will mark this feeder orange with the status "Too slow".

The SmartFeeder 2x8mmXi feeder module can be operated at any machine which can already

accommodate the SmartFeeder 2x8mmX. The SmartFeeder 2x8mmXi can also be operated with

older station software versions 7xx.x.

For more information about introducing the SmartFeederXi, refer to the technical information "In-

troducing the SmartFeeder modules Xi" (German [TI2018-09D14], English [TI201809E14]).

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.1 Front sliding guide/sliding foil

172 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

8.1 Front sliding guide/sliding foil

Spare part required

Fig.55: Sliding foil X-Feeder

Feeder module Item no. Designation

SmartFeeder 2x8mmX

SmartFeeder 2x8mmXi

03019604Sxx Front sliding guide

Tools required

●

Sliding foil remover

8.1.1 Removing the Sliding Foil

► Place the feeder on a stable, level and clean sur-

face.

► Insert the sliding foil remover into the sliding

guide.(1)

► Lever the sliding foil out of the engaged position.

► Lever the sliding foil until it has been turned by

approximately90°.

► Push the sliding foil towards the front and out of

the sliding guide.(2)

8.1.2 Fitting the Sliding Foil

► Press the sliding foil slightly together.

► Push the sliding foil from the front into the sliding guide, until it engages.